Your cart is empty.
Your cart is empty.Product Description
The Bike Brake Pads is highly recognized and praised by consumers:
Twill drains prevent sand, mud and stones from wearing rims. Curved design provides effective braking in most severe weather conditions. The brake pads made of high-quality nitrile rubber is wear-resistant, heat-resistant and noise free.
We not only control cost strictly, but also minimize the profits for higher sales, which in turn bring about high quality and lower prices. We are so proud of it for gaining numerous positive reviews.
Applications:
These v-brake pads are suitable for most 20”+ MTB , Cruiser Bike, Folding Bicycle, Mountain Bike, Road Bike and others using V-brakes
Specification:
- Package includes:: 4 x V brake pads (2 pairs)
- Material: High quality nitrile rubber and aluminum alloy
- Accessory: 1* Allen wrench
Bill
Reviewed in the United States on March 9, 2025
Long lasting
Hapuna
Reviewed in the United States on January 18, 2025
I was hesitant to buy these. I figured they would make a squeel. They do not. Quiet. What a relief from the old brakes.
NM
Reviewed in the United States on September 14, 2024
These are a good option if you are on a very tight budget, but for only a couple of dollars more there is at least one other pair that works better.To be clear, these work fine - they stop adequately on my very low-powered e-bike (250W motor), I do feel they are a little soft and I wind-up squeezing harder. I'm comparing this to an identical bike that I have the other set of overnight/one-day brakes. I feel there is about a foot difference when coming to a stop traveling at ~12 mph to the other pair. (I tend not to ride much faster than that because of traffic considerations.) If you tend to ride faster than that or up/down hills, I recommend upgrading.Here are my main gripes - the angled grooves ("water guide") on it make it hard to ascertain wear without pulling the brake away. The same grooves don't help any better with removing water than straight up/down cuts. The material is a bit softer, which probably makes them silent but does require squeezing harder to stop. (I guess you don't have to worry about toe angle with these...)The included 5mm Allen wrench is adequate for changing these brakes, but I'd avoid using it on other bolts because it is a bit sharper than sets you normally buy and will mar the bolt. (If I'm not in a rush, I reach for my Allen wrenches with ball ends to better maintain the bolts.)Overall these are good, but you may want to spend a little more for the better. They are great for most casual riders, but if you commute and these are part of your daily ride - I'd urge you to upgrade.
Robert Cordell
Reviewed in the United States on August 7, 2024
I found a junk BMX bike in the trash to be picked up. The brakes were close to gone. These went right on, nice hardware, good braking, no squeaks.
Z600User
Reviewed in the United States on June 27, 2024
Very easy to install, tool provided, eliminated squealing of brakes. Installation of new brake pads was worth the time, effort, and cost. It made me want to ride the bike again regularly. It was about the lowest cost pads available for the type of brake pad I needed, and was shipped promptly, arriving in a reasonable time frame. I will enjoy bike riding again for some time. When installing, take care to squeeze brake before tightening the pad, in order to align the pad properly with the rim.
Ddl
Reviewed in the United States on November 9, 2024
It fit just fine and was easy to install.
Aptly
Reviewed in the United States on April 22, 2024
First time replacing brake pads. Easy to install. Seem to do the job as well as any. Just installed, so longevity is not measurable. I suspect they will work fine for the funds invested.
William F Metcalf
Reviewed in Australia on August 29, 2020
Good price good fit, good design
Lee Leavelle
Reviewed in the United States on November 20, 2019
So save all of the cups and cones from your original pads when you install. When I went to install these by the time I stacked up all of the little washers, cones and cups that are necessary to align the pads there was not enough bolt left to tighten the nut, almost stripped it. I took a close look and realized that each little component was built just a tiny bit thicker than the original ones. When you add it all up it didn’t work. So I used all of the old washers, cones and cups and completed the install with no other problems.The brake pads are quiet and seem to work well. I think they are quieter because the rubber compound is softer than original so they may not last as long. We will see.
Recommended Products