Your cart is empty.
Your cart is empty.No one enjoys scrubbing off stubborn, dried-up bug guts after a long road trip. That’s where the Bugflector II comes in. The high-profile wrap-around design provides maximum protection from all bugs, big and small, while its off-the-hood design allows for easy cleaning and waxing. Made from durable impact-resistant acrylic, the Bugflector II can stand up to everything from car washes and bugs to the wear and tear of daily driving or going off-road. Custom-molded to fit your vehicle’s exact year, make, and model and contoured to fit the curves of your hood. Available in dark smoke finish and proudly made in the USA with global materials.
Roger D.
Reviewed in the United States on March 6, 2025
Will not work on a 2024 ford explorer. Tried to install different ways and can’t get hood shut. Would not recommend it because it is very brittle and broke trying to install closing hood. Not what i expected from the manufacturer AVS. I noticed when i went into( have a product question ) it only fits 2020-2023 which was not advertised. Very upset.
Pops75
Reviewed in the United States on March 12, 2025
High Quality. Every vehicle I drive frequently have these.
Wilson
Reviewed in the United States on September 3, 2024
Put on my 2024 Ford Explorer XLT. Nice flush mount using the applied 2-sided applique tape. Peel and stick. Flush mount nice because no debris, dirt or leaves can get in-between the deflector and hood paint.
Jon Evans
Reviewed in the United States on May 17, 2024
Perfectly molded for the 2022 Explorer. Chrome looks amazing. Tedious to install but if you carefully follow the instructions and checkout the installation video, the outcome looks excellent. Measure twice, tape once!
Charles Franz
Reviewed in the United States on February 27, 2024
Installed deflector exactly as outlined in instructions. Hood would not close all the way. only closed to first latch. Recommend Aeroskin deflector that is installed with adhesive tape.
Duane
Reviewed in the United States on April 25, 2024
Installed in about 10 minutes. Used my trim puller and pulled the rubber from under the hood edge. Used the supplied pins and installed the bug deflector. Removed the pins on the rubber that were taken up by the deflector and reinstalled the rubber seal. Everything works good. It did add just a touch of wind noise going down the highway. The ones I have added to my F150s have all done the same thing. It redirectes the air up and it hits at the top of the window, but that is the intention of it.
Salem Green
Reviewed in the United States on April 18, 2024
I watched the video, prepped the vehicle, then installed the deflector. It looks nice, fit was very good. However, it's nearly invisible on my Explorer. I enclosed a photo for you to judge. I'll test it out this weekend. I've already had three rock hits in 3,000 miles. Hoping this will help reduce the damage.
John adrian
Reviewed in Canada on February 12, 2023
Easy to install...great product
James borges
Reviewed in Canada on December 1, 2022
Went on nice and easy. Looks good and saves my hood from getting chipped.
T. Vex
Reviewed in the United States on November 2, 2022
Installed this on our new Explorer Timberline. Was surprised to find that it is simply a flush fit shroud, rather than having a curl up on the trailing edge to help defect bugs upward with airflow. That said, it was a good form fit and at least it will protect the front face of the hood so I kept it. For now.Subtracted a star because of the time I had to spend cleaning the inside face. A baggie with the prep wipes had been taped to the underside of the shroud with packing tape, which left a lot of adhesive residue when removed. Also a sticker, with the same issue. Because this is semi opaque polymer I was worried it might show in full sun. Took 20 minutes of very judiciously using Goo Gone to clean all that off.Install tips:- In the pic you will see a rubber seam roller on the hood that is quite helpful in applying firm pressure (BEFORE you remove the outer protective film) to the 3M tape to ensure good adhesion.- The online instructions recommend taping off the hood before you prep the surface - DO NOT skip this step IF you use the prep pad; it smells like acetone and it attacks the clear coat. Had I known it was so chemically aggressive I wouldn’t have used it. Having installed a lot of things with 3M automotive tape, I think a good thorough cleaning with alcohol to remove any wax would be sufficient without risking damaging the paint.- Have extra alcohol on hand if you car has been waxed; only one small wipe was provided, which isn’t adequate to remove residual wax from an area that large.- Note the instructions also state not to drive the vehicle for 24 hours; ridiculous. Lawyers hard at work.
KittyFallDown
Reviewed in Canada on May 8, 2021
Very impressed. A perfect fit and it looks great! Took 5 mins total to install and love it!
Recommended Products
