Your cart is empty.
Your cart is empty.Specifically designed to stand up to the wear and tear of off-roading and trail riding, Trail Armor Front Cowl Guards protect your Jeep and look good with their rugged features and OEM matte black finish. Make sure leaves, dirt, and other debris stay on the trail and out of your Jeep. Cowl Guards provide protection for the gap between your vehicle's hood and windshield, preventing any unwanted elements from getting into the windshield wiper system or cabin filter. Made from durable TPO material to protect the cowl of your Jeep. Includes 2 Cowl Guard covers. Trail Armor Cowl Guards use doubly secure 3M automotive adhesive. Each product comes with instructions and all necessary hardware. Bushwacker's Trail Armor Front Corner Covers are proudly built in the United States and backed by a Limited Lifetime Warranty.
Chad
Reviewed in the United States on May 31, 2024
I had to remove my factory rock rails and drill out the holes to reinstall rails. Took a bit of finesse to get them to align with the added width of the guards. All and all came out nice I have a feeling the tape will need to be replaced at some point. It doesn’t want to sit completely flush and front and rear overhang in fender wells a bit. Overall looks decent and will do the job.
Matthew H. Young
Reviewed in the United States on January 23, 2024
I had them on my other Jeep so I had to put it on the new one I just bought (2023 Wrangler Rubicon). Covers the door sills and under doors for chip protection against rocks, tree limbs, and dirt. Looks great while it's protecting your investment. Kind of a pain to put on. Start from the top and work your way down for sticking the 3M tape to your vehicle. You can unstick the tape with a blow dryer.
Sandra Leisure
Reviewed in the United States on July 8, 2023
The media could not be loaded.
Eric Parisien
Reviewed in Canada on March 30, 2023
Super easy to install with a very good 3M adhesive.Looks very nice.Only flaw, the guards cover the bottom screws of the cowl, so I you need to access them, you will either have to remove with a heat gun and destroy the guard or pierce wholes on the guards to access the screws (which I will have to do...They should make the wholes covers screwable or something.
SIM
Reviewed in the United States on March 18, 2023
This was a perfect fit for a 2023 Wrangler 2 door. I have used bushwacker parts before and they are good quality. This was good neat finished edges and looks OEM. Just know that this covers up all the holes under rocker where you would need to put the bolts through for mounting running boards. It should be easy enough to drill out the holes since it is just plastic if you do want to mount running boards.Be very sure to clean all the surface where you will be gluing this onto to make sure you get good adhesion. that is critical to a proper installation or else the adhesion will fail. This is the case with anything for automotive where you are using 3m double side tape.Lets see how well the glue holds up over time. Overall happy with the product but I feel it is a bit overpriced. But ultimately you get what you pay for. I will update this review if i have any issues.
Scott Lambert
Reviewed in the United States on March 25, 2022
Installed on a 2018 JL 4 door sport. Took less then an hour to do. This is the second jeep I've done and they really tighten up the looks of rocker panels. The covers hide unsightly bolt holes at the bottom of the rockers, and protect the sill tops from boot scuffs. It is important to thoroughly clean the area where the guard is going to go on with rubbing alchohol. You are supplied with a couple small towlettes, but I used more on a towel. Install at warmer temperatures. "Pre-fit" with the adhesive tape covered because there is a little wiggle room front to rear. I used masking tape to hold and align them. Worked great. I give this little project a "10".Scott
Francisco A.
Reviewed in the United States on December 2, 2022
Great little accessory to jeep. Not sure why it indicates that it will not fit a Gladiator JT. As you can see it's a perfect fit. Would recommend for Gladiators.
stephane
Reviewed in Canada on September 1, 2021
fit très bien sur mon jeep jl et facile a installer
dodge.guy
Reviewed in Canada on March 27, 2021
seems to fit just not warm enough to put on yet
Customer
Reviewed in the United States on February 25, 2021
Very dissatisfied. Not only is this product pricey but it came warped and deformed. The box was crushed and half opened.The product itself is extremely poor quality. If you think this will protect your Jeep, think again. It will be fine if a stick hits it, if a rock or branch hits it, the plastic is too thin to protect your vehicle.The adhesive strips are 1/4" wide and surround the edges, too easy for a stick to pop it off. No support or rigidity on the inside to prevent damage.It's plastic, it's cheap and it's not what you want to protect the corner of your Jeep. And for $150+? No value at all. This is a $50 product at best.
Lat
Reviewed in Canada on February 20, 2020
I shopped around for these rocker panel panel protectors, great price and quality. A bit of the adhesion is coming off of one but it is winter in Canada so I kind of expected it to take a beating.
GGaron
Reviewed in Canada on January 3, 2020
49$cad Waterhouse deal so it's nice
cj
Reviewed in the United States on June 4, 2019
Normally I am a fan of bushwacker products. Though I like the finished product very much, This is NOT a peel and stick product. If you have Stock Running board like a Sahara Unlimited then you have to remove the running boards and make holes in the product for the running board brackets. Then there are two holes that have to be drilled where the lower front fender bolts on the JL Wrangler mount. All of this could have been easily accomplished by Bushwacker in a jig assembly at the factory. AS far as ease of installation, this was an epic fail on the manufacturer's part. The finished product though looks awesome and should protect the Rocker Panels from being beat up.
Recommended Products
$17.99
$ 8 .99 $8.99