Your cart is empty.
Your cart is empty.Buyers Products Rubber Hood Catch is a weather-resistant hold-down that is ideal for hoods, vehicle compartments, and more. The heavy duty rubber catch stretches over the bracket to create a strong closure. Choose from an "A" or "U" shaped bracket. Catch is also available in a mini 2-1/2 in. size.
Dean
Reviewed in Canada on July 27, 2024
Good latch for the price
G&B
Reviewed in the United States on July 24, 2024
I used these after hinging the rear cover on my excavator. They hold well with no play because they are short.
Jake of the North
Reviewed in Canada on November 1, 2024
Worked great to hold a side panel on my mower conditioner after the retaining clips got damaged. Actual John Deere parts were very expensive and I adapted these to work without much fuss.
Peter Hillar
Reviewed in Canada on October 21, 2024
small and well made
MARK.
Reviewed in Canada on October 1, 2024
Perfect for my application
ibnracin
Reviewed in the United States on August 31, 2022
Was exactly like the one on my RV easy to change out
MICHAEL R.
Reviewed in the United States on July 27, 2022
a little smaller than expected
Kat
Reviewed in Canada on October 18, 2022
Were smaller than I thought..and could not use them for my purpose. But nothing wrong with the product
Kindle Customer
Reviewed in the United States on July 9, 2021
worked, was shorter but we got it secured tractor is from 1988
cmpk24
Reviewed in the United States on January 28, 2019
this is a miniature latch - didn't pay close enough attention to the description. the rubber latch measures about an inch or so in length. it still worked for my purposes regardless of the smaller size.
Hambone33
Reviewed in the United States on January 23, 2017
Product is as advertised and was the right size to replace the cracked rubbers on my trailer. I only needed the rubber parts since my hardware was fine. It was the same product as what was on my 2014 Keystone Cougar camp trailer. Make sure you are getting the correct length because you are not going to stretch this material beyond the length is was made to fit. The rubber is very strong and hard for me to pull far enough to fit the front clip even though it is exactly the same unstretched length as the original. Worked for me.
Steve Iott
Reviewed in the United States on April 3, 2017
Item was exactly as described. Worked perfect with a little engineering to the application I was using it for. I used bolts to secure the hinge to the cargo box I was putting them on, because like others say, these don't have much stretch to them, so I wanted to be sure I wasn't going to rip them out easily by using small little screws. Great price as well. Very happy.
Andre A. Martel
Reviewed in the United States on March 19, 2012
Perfect. Just fixed my Coleman Coolbox cooler.If you own the Coleman Coolbox Cooler/Radio/CD these are the replacement latches that you need. These are stronger than the original and have a smaller tee on the handle. Since your cooler is mounted with one screw just use the rubber latch by it self with the pin/washer and cotter pin that come with the parts bag. All you have to do is cut the old pin off your cooler latch using a hack saw or Dremel cutoff disk. Remove the new Tee and retainer pin from the new latch. It is held in with a cotter pin or apart inside the zip lock bag. Slide the pin through the cooler bracket and the new latch. Install the washer on the outside of the pin and attach the cotter pin. Now bend the cotter pin to retain it on the latch. You can also replace the new latch pin/cotter pin with a screw pin or a screw with acorn nut available at you local ACE hardware that will eliminate the cotter pin that catches on clothing.
Recommended Products
$13.15
$ 6 .99 $6.99
$25.20
$ 11 .99 $11.99
$125.99
$ 50 .99 $50.99