Your cart is empty.
Your cart is empty.This engine oil cooler hose assembly matches the fit and function of the original equipment components for reliable repair and restoration of proper oil circulation between the oil cooler and engine. This part is compatible with the following vehicles. Before purchasing, enter your vehicle trim in the garage tool to confirm fitment. [Chevrolet S10 Blazer: 1988, 1989, 1990, 1991, 1992, 1993, 1994] - [Chevrolet S10: 1988, 1989, 1990, 1991, 1992, 1993] - [GMC Jimmy: 1992, 1993, 1994] - [GMC S15 Jimmy: 1988, 1989, 1990, 1991] - [GMC S15: 1988, 1989, 1990] - [GMC Sonoma: 1991, 1992, 1993] - [GMC Syclone: 1991] - [GMC Typhoon: 1992, 1993] - [Oldsmobile Bravada: 1991, 1992, 1993, 1994]
Cesar
Reviewed in Mexico on October 2, 2021
Buen producto para una 91 blazer s10
Samuel Howerter
Reviewed in the United States on June 29, 2020
Worked as described on a 1989 Chevy S10 Blazer. Appears to be good quality and comes with the required gaskets.
Reuben
Reviewed in the United States on September 21, 2018
They fit but we're hard as hell to install. Had to jack the engine up to gain clearance, they were close but bend was a little off so I had to use a jack to press them into the truck housing
Arturo
Reviewed in the United States on March 14, 2015
Good part
Practical Reviewer
Reviewed in the United States on January 27, 2015
Dorman's quality is seriously lacking. I have 2 s10 trucks, 3 sets of these crappy oil lines started leaking last winter when the temperature went below 0 degrees. My 93 truck lived in Alaska for 10 years and never leaked in the cold temps. The original Delco lines were much better quality. Everything I have bought made by Dorman in the last 3 years is substandard. The hinges for the truck doors made by them last about 3 months, had to buy original oem hinge bushings. The only good thing I can say is they replace these weeping wet oil lines every time they go bad. Avoid Dorman.
David G Miller
Reviewed in the United States on November 13, 2013
Product works well and does not leak, mine has been installed about 2 years. It is a POS to install, but that is not the fault of the part.
Jennifer Taylor
Reviewed in the United States on April 5, 2012
Noticed the old lines were seeping and after about a year noticed the oil pressure gauge acting all out of wack. So I decided to change the lines. This fixed my problem right up. Havent had any issues since.
Smithsonite
Reviewed in the United States on October 24, 2011
Not much to say - they're new. Installed on a '00 GMC Jimmy engine that went into a '89 S10 Blazer. Yes - they fit right on the '00 engine! The real test will be a few seasons of heat, vibration, & 100°+ temperature variations. Came with only one side covered in protective loom, so I grabbed a section off a junk I have here & did the other side as well. With such a critical part to the life of the engine, I don't want to take any chances with abrasion. The price was right, but they are made in China .... just so you know. Time will tell if I made the right choice here.**UPDATE 2/18/2013**5 years was wishful thinking. Leaks near the filter after just one year of use. Not bad enough to warrant a replacement ... but if I had to do this again, I'd have found a better quality (read: NOT made in China) replacement. Be aware ...
Dennisjl
Reviewed in the United States on July 3, 2010
I purchased this online because the local auto stores wanted $50-79 for this hose assembly. It works as it should, shipment was fairly quick, but the packaging...all I could do when it arrived was chuckle, I could fit SIX mid tower computer cases plus a small child in the box that it arrived in.
Recommended Products
$30.72
$ 13 .99 $13.99