Your cart is empty.
Your cart is empty.The flimsy plastic end on the original automatic transmission shifter cable on certain Toyota, Lexus, and Scion vehicles tends to wear and split, causing sloppy or unpredictable gear shifting and eventually rendering the vehicle inoperable. This patented Dorman OE FIX shift cable repair kit replaces the plastic shift cable end joint with a durable steel joint, saving the expense of replacing the entire cable, providing a longer-lasting, more reliable repair, and restoring precise, predictable shifts. This part is compatible with the following vehicles. Before purchasing, enter your vehicle trim in the garage tool to confirm fitment. [Lexus RX300: 2000, 2001, 2002, 2003] - [Toyota Avalon: 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004] - [Toyota Camry: 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005, 2006] - [Toyota Corolla: 2003, 2004, 2005, 2006, 2007, 2008] - [Toyota Echo: 2000, 2001, 2002, 2003, 2004, 2005] - [Toyota Highlander: 2001, 2002, 2003, 2004] - [Toyota Matrix: 2003, 2004, 2005, 2006, 2007, 2008] - [Toyota RAV4: 2001, 2002, 2003, 2004, 2005] - [Toyota Sequoia: 2001, 2002, 2003, 2004, 2005] - [Toyota Sienna: 2004, 2005, 2006, 2007, 2008, 2009, 2010] - [Toyota Tundra: 2003, 2004, 2005]
Tony
Reviewed in the United States on January 30, 2025
this item did not work with my cable
Mark
Reviewed in Canada on September 6, 2024
So close... Had to modify to make it fit. The end piece on the cable fit the clip side, but not the main piece. So, I shortened the cable end to fit the both sides only to find that the center was bigger than the opening in the part. So drilled that out with a slightly larger bit and made the slope less steep with a 17/32 bit. That did it, and it works great. Much cheaper than the $800+ the Toyota dealer quoted to replace the cable.
Farid Mohtadi
Reviewed in Canada on September 24, 2024
Excellent quality and fit. Very good part , many uses.I used it in the car engine, the cable end was broken, this fixed it in 5 minutes installed
motorfortoy
Reviewed in Canada on September 22, 2024
used it on a 2003 toyota Highlander shift linkage at trans
Joseph Avallone
Reviewed in the United States on August 1, 2024
Worked great on my 98 Camry. Just had to drill out the hole a bit due to my shifter linkage bold swelling up a bit from rust over the years. Worked great way better than replacing whole shifter cable and will last longer than that crap plastic on the oem cable
Herman
Reviewed in the United States on July 12, 2024
This fit perfectly in my 2000 Camry (4 cylinder).This Toyota was made in Lexington, KY.When the cable end broke I started looking for a replacement cable, I saw that there were two different types of cables depending if the car was made in Japan or in America.I'm not sure but I suspect that the design of the cable ends could be different?One cacavet: just be careful when tightening the main nut, with the split design of the threads I could easily see someone stripping these by overdoing it.
johnny5c
Reviewed in the United States on June 9, 2024
In order for this to fit a 2002 Lexus RX300 you need to spend a lot of time grinding out the inside to fit the stock shift cable. I gave it more than one star just because it still takes longer to replace the whole cable.
rt
Reviewed in the United States on June 24, 2024
Read the reviews. I had to do what one buyer said. I used a drumle grinder to get it to fit. Took 2 hours. Just buy a oem cable save you a headache.
Marcus
Reviewed in the United States on October 3, 2024
I used this on my 06 scion xb at the transmission bracket. Just like a lot of other reviews said, it does need to be modified. You’ll need a dremel tool and have to hollow out the inside of the connector.
Joe and Caroline
Reviewed in the United States on October 13, 2024
Worked great on 99 camry
ShapeShifter
Reviewed in the United States on December 6, 2023
I have a 97 Camry v6 xle. The shifter cable broke right at the transmission. Toyota employs a hard plastic seat ( that broke ) to affix the cable to the eyelet. Thanks to the dorman engineers for this fix. The entire cable for the v6 is not available on the internet nor Toyota. After reading a prior review I was skeptical but I bought the part. After 2 minutes of removing the broken plastic the dorman part was on and is way better than new. If it took you more than 2 minutes to install then your doing something wrong. If your the type that believes a square peg fits in a round hole then this part is not for you. Just be careful when manipulating the old cable as you do not want to kink it or damage the sleeve. This saved me multiple hours of work.
Recommended Products
$10.90
$ 5 .99 $5.99