Your cart is empty.
Your cart is empty.Original equipment brake lines are highly rust prone. This Dorman OE FIX brake hydraulic line kit is made of upgraded stainless steel to resist corrosion. It's also pre-formed to fit specific vehicle applications for easier installation. This part is compatible with the following vehicles. Before purchasing, enter your vehicle trim in the garage tool to confirm fitment. [Chevrolet Silverado 1500 HD Classic: 2007] - [Chevrolet Silverado 1500 HD: 2003, 2005, 2006] - [Chevrolet Silverado 1500: 2005, 2006] - [Chevrolet Silverado 2500: 2004] - [GMC Sierra 1500 HD Classic: 2007] - [GMC Sierra 1500 HD: 2003, 2005, 2006] - [GMC Sierra 1500: 2005] - [GMC Sierra 2500: 2004]
Mat kirsch
Reviewed in the United States on February 7, 2025
This is a great brake line kit like all Dorman parts excellent product, the kit is a perfect fit and all the fittings were correct , the job to do it does take some time routing the lines correctly I have a very rusty 2004 Chevy 2500 crew cab that we have been patching the brake lines as they break, but just buy the kit and do them all at once the first time one rusts through because the others are not far behind , great product so happy they are making kits like these they save so much time over trying to find the correct lines or fitting sizes , thanks Dorman
Customer
Reviewed in the United States on September 3, 2024
Worked well, not fun.
I actually bought this
Reviewed in the United States on June 15, 2023
Replaced on a 2003 Silverado 1500hd Honestly idk if the money saved doing these myself was worth it😂 Only prep i did was to remove driver side inner fender. Line removal was easy cut the lines take them out in pieces. But trying to sneak these pre bent lines back in was a pain in the *** .. Front passenger and rear line was the worst. Front driver , front and rear master cylinder supply were fairly easy. Used a might vac hand vacuum pump to bleed lines then went around and did the old pump and hold to finish it off. I did this solo but if you had a buddy that would help allot. If I had to go back I would maybe just get the pre cut rolled lines run and bend those myself I think that woulda turned it into a fairly quick job. Just not as pretty.Ps. Be careful you don't break off bleeder valves. If your replacing cause your lines rusted out might as well get new bleeder valves while your at it there only a few dollars
Janet
Reviewed in the United States on October 6, 2021
It fits perfect.
Wendy Fyfe
Reviewed in Canada on August 25, 2020
I love these kits saves a bunch of time on what would be a very nasty job... these are stainless too so that is so much better than piece mealing the carbon steel autoparts store ones.
joeseph
Reviewed in the United States on December 24, 2019
Real stainless steel fit great
Brayden Burdeniuk
Reviewed in Canada on November 9, 2019
Good
B Travis
Reviewed in the United States on October 30, 2019
Easy install - within 30 minutes. Only need one line, currently, but buying the set was cheaper than just the one I need.
J Mood
Reviewed in the United States on October 2, 2019
Fits and works as it should highly recommend for chevy guys and gals
Kevin
Reviewed in the United States on November 2, 2018
Bought this kit to replace my corroded brake lines on my 2004 Chevy Silverado 2500. Brake lines were a nightmare to install but well worth the money I saved. the dealership wanted to charge me close to 1000 dollars and I was able to fix the truck myself for less then 200. Don't be intimidated, replacing brake lines can be done by anyone. Just know it's about a 10 hour job.
Recommended Products
