Shopping Cart

Your cart is empty.

Your cart is empty.

Inner Axle Side Seal Installation Tool with Storage Case For Dana 30/44/60 Front & Rear Differentials Compatible with Jeep, Ford, Dodge, Volve Chevrolet, GMC, International Scout, Jaguar, Isuzu

5.0 Write Review
Free shipping on orders over $29.99

$29.99

$ 13 .99 $13.99

In Stock
  • APPLICATION -- This tool will work on Dana 30,44 and 60 front and rear differentials found on for Chevrolet, Dodge, Ford, GMC, International Scout, Jaguar, Isuzu Rodeo, Jeep, Mercury Mariner, Volvo and some other applications as well.
  • PACKAGE CONTENT -- 1 * Inner Axle Side Seal Installation Tool, 1 * Molded Storage Case.
  • FUNCTION -- Helps install inner front axles seal to the proper depth. Specially designed to safely and evenly apply pressure to the inner axle seal to press it into the axle housing without damaging the seal.
  • UPGRADE DESIGN -- The different inner and outer size of the puck suitable to press on many different seals. Customized nut-full doesn’t need to worry about the wrench falling off during the installation process. A must have for replace broken or bad Inner Axle Side Seal.
  • EASY INSTALLATION -- Hassle-free installation.1. Place the seal into the differential axle tube, aligning puck with the seal and the flat end of the bolt; 2. Tighten the nut with a wrench until the seal is properly seated; 3. Remove the tool and the seal is installed. Do the same to the other side.
  • TOP QUALITY -- Manufactured from quality steel for long tool life. Long lasting durability zinc black coating used on tool to protect them from all the dirt, oil, and grease that could potentially break down the socket quality. Corrosion-resistant, wear-resistant, and rust-resistant.
  • SATISFACTION GUARANTEE -- If you are not satisfied with Camoo products, simply return it for a full-refund in 30 days. Guarantee with 12 months warranty. No worry about buying!


Product Description

Inner Axle Side Seal Installation Tool For Dana 30/44/60 Front Differential

1
The video showcases the product in use.The video guides you through product setup.The video compares multiple products.The video shows the product being unpacked.

hero-video

Merchant Video

Fitment References

1

Used to Install Front Left & Right Axle Side Seal

1
1

How To?

1

Step 1

  • Remove the wheels and axle hub/seal assembly.
  • Remove the vacuum disconnect. Remove the differential cover & drain the fluid.
1

Step 2

  • Remove the axle shafts.
  • Remove the gear carrier, being careful to mark the bearing caps and bearing races.
1

Step 3

  • Remove the old seal, which sits just inside the axle tube where it meets the pumpkin, with a pry bar.
1

Step 4

  • Press the new seal into place
  • Install everything you removed, in reverse order.

Product Details

1

Installer stud

  • Manufactured from quality steel. Specially designed for Dana 30, 44 and 60 front differentials.
1

Installer puck

  • Upgrade puck is designed to grab a variety of different sealing rings.
1

Thrust bearing

  • Simplify the process when install the axle Seal. Great Time Saver! The way safer/easier to use than the old punch and hammer.
1

Nut-full

  • Customized nut-full doesn’t need to worry about the wrench falling off during the installation process.

The Most Popular Tools For Dana Differentials

Application

  • For Dana 30/44/60 Front differentials.

Application

  • GM 10 and 12 bolt, for Ford 9”, 7.5", 8.8", 8”, for Dana 30, 35, 44, 50,60,70,80

5 Piece

  • Set contains 5 of the most popular sized spindle nut sockets.

Function

  • Seals keeping mud and debris out of your front axle tubes. Helps install seals.

Function

  • Makes setting pinion depth more accurate and quickly. Measure many Differentals.

1/2” Drive

  • Drive sockets with a 1/2 inch square drive impact wrench or hand tighten.