Your cart is empty.
Your cart is empty.Product Description
About Us
As the pioneer of DTC precision rifle optics and accessories, we continue to challenge the limits of quality and affordability.
- 15+ Years of Optic Experience
- Dedicated Service Department
- Based in California
Monstrum Picatinny Micro Red Dot Ring Mount for Rifle Scopes
The Monstrum Micro Red Dot Ring Mount for Rifle Scopes is built for mounting a red dot sight as a secondary sighting system directly to your rifle scope tube. This setup allows for fast transition between your rifle scope and a 1x power red dot optic for use at closer ranges.
- For mounting of Picatinny base red dot sights as a secondary sighting system directly to your rifle scope tube
- Allows for fast transition between your rifle scope and a 1x power red dot optic for use at closer ranges
- Picatinny rail mount accepts red dots with a standard Picatinny base
- Ring mount fastens around your scope tube, installing via two set screws and included hex key
Donnie Linville
Reviewed in the United States on March 9, 2025
Wasn't exactly what I thought it was for, but the product is definitely well built
Bennett-Johnsons
Reviewed in the United States on February 25, 2025
Exactly like the picture
Heathen
Reviewed in the United States on February 24, 2025
So the mount has a few big issues, first it’s ring diameter is just a tad too small and may crush your scope if not careful. But the other huge issues that had rendered the item useless is the junction on the top ring where the 2 screws hold the section of picatiny on top, well it completely snapped in half from 20 lb/in on the 2 screws. This is nothing in regards to torque, whatever aluminum this is if it even is it could be zinc, is terrible. And you have to torque the pic rail I tried it lightly hand tight and it wobbled once ring was torqued, so I tried 10 lb/in, then 15, and at 20 it just broke right in the middle along the 2 holes. 20 lbs/in is nothing, I’m not even gonna bother returning, I am trying jbwelding the two pieces together to the rail with screws in and I have more faith in the job weld holding than the original product. 20 dollars I can chalk up to science for the masses. I’m gonna buy a trijicon mount instead. The picture is after I’ve applied jb weld
Norsky in Nampa
Reviewed in the United States on February 8, 2024
Used the product to mount a light/laser sight on a tactical shotgun. The product arrived quickly. Well packaged. The product is well designed and built. Substantial bulk to handle it's intended use without failing. Nicely contoured-edges have been rounded. Looks impressive. Well finished. Only time can tell, but as an engineer and a metalworker, I expect this to last forever.
Tom
Reviewed in the United States on February 18, 2024
Bought this to mount phone to crossbow so I could record Hunting video's. Typically I would have to put my bow down, pull out my phone to record deer that are walking past my stand. This held the phone mount well. Screws all lined up perfect and securely tightened down on the scope.
B Felkel
Reviewed in the United States on December 29, 2024
I would give this product a perfect score but unfortunately I can't. I decided to use this on-top of a scope I had for a .308 build I have been working on. I used a budget GDS and zero'd it at roughly 50 yds since the scope I was using wouldn't perfectly sit on the crosshair for anything less than 100yds. After having zero'd everything I went to turn the GDS off and noticed it was wobbling considerably. Took me a minute to trouble shoot but eventually discovered the picatinny mount for the rings wasn't tightened properly and walked loose after only 4 shots from a .308. What was even more annoying was there was no included allen wrench hardware to loosen/tighten the picatinny mount, just the rings to the host scope. I had no choice but to remove the piggyback mount and fix it when I got home. The fix was simple and some blue loctite ensures it won't walk loose again but it was a big inconvenience at the time of shooting on the range. 4/5, make sure you check your screws holding down the picatinny mount before ever mounting it to a scope!
Justin McDonald
Reviewed in the United States on July 28, 2023
Much higher quality then the old gen 1 version of this I had purchased in the past and hated. Came with all tools and hardware. I took all the screws out including the rail screws, blue loctited them, then installed the ring on my 3-12 at 12Oclock to Mount a small RMR pic rail red dot for my SPR type build. Torqued screws down to 15 inch lbs. Works fantastic. Great quality for the price!
Raleigh Littles
Reviewed in the United States on July 23, 2022
I bought this scope ring so that I could mount a red dot on top of my LVPO. One issue I ran into is that the spacing for the screws was a bit bigger than my LVPO's rings, so I couldn't get both screws to fit (I could either mount the front one or the back one). I'll unfortunately have to end up returning this product because of that.Despite the fitting issue, the product otherwise seems fine. It's built of aluminum and seems like it would be reasonably sturdy enough to use. The rail is just long enough for me to put a sight on, but not long enough that it interferes with the windage dial on my LVPO.
Recommended Products
$39.99
$ 19 .99 $19.99