Shopping Cart

Your cart is empty.

Your cart is empty.

Monstrum Shrapnel Offset Picatinny Riser Mount with Recoil Stop Base | 8 Slot 3.5 inch

Free shipping on orders over $29.99

$19.99

$ 8 .99 $8.99

In Stock

1.StyleName:Low Profile


  • Low profile offset picatinny riser mount with 1.5 inches of forward extension for more flexible optic placement and eye relief positioning
  • Picatinny base measures 2 inches (or 4 picatinny slots) in length while the top rail measures 30 inches (8 total picatinny slots). The rail extends an extra 1.5 inches over the front of the base, allowing for more forward positioning of long eye relief optics
  • Available in low and medium profile heights. The low profile mount provides 0.42 inches of rise over the receiver rail. The medium profile provides 0.88 inches of rise.
  • Picatinny base is equipped with custom recoil stop bolts that slot seamlessly into your Picatinny rail with zero wiggle - guaranteed to hold zero against the toughest of recoil
  • Single piece machined 6061 grade aluminum profile is designed to shave off precious ounces of weight



Product Description

RM101

Monstrum Logo
About Us

As the pioneer of DTC precision rifle optics and accessories, we continue to challenge the limits of quality and affordability.

  • 15+ Years of Optic Experience
  • Dedicated Service Department
  • Based in California

Shrapnel Offset Picatinny Riser Mount

  • Low profile offset picatinny riser mount with 1.5 inches of forward extension for more flexible optic placement and eye relief positioning
  • Picatinny base measures 2 inches (or 4 picatinny slots) in length while the top rail measures 30 inches (8 total picatinny slots).
  • The rail extends an extra 1.5 inches over the front of the base, allowing for more forward positioning of long eye relief optics
  • Picatinny base is equipped with custom recoil stop bolts that slot seamlessly into your Picatinny rail with zero wiggle - guaranteed to hold zero against the toughest of recoil
  • Single piece machined 6061 grade aluminum profile is designed to shave off precious ounces of weight

Technical Specifications

Total Length: 3.46 inches
Height: Low: 0.42 inches of rise | Medium: 0.88 inches of rise
Weight: 2.5 oz
Material: 6061 Aircraft Grade Aluminum
Rail Type: Picatinny
Mount Type: Picatinny

Tj
Reviewed in the United States on February 25, 2025
Work great to add a second IR on my rifle.
Customer
Reviewed in the United States on September 29, 2024
Not a bad product, but too short for my needs. Holds onto rail well, just need a few more slots.
Joe T.
Reviewed in the United States on September 18, 2024
Actually a really solid mount for the price. Zero complaints. Holds zero, three tightening bolts, good finish, lightweight.Its good to go.
J. Oliver
Reviewed in the United States on February 16, 2024
Good piece here--nice finish, no burrs/marks, lines up and mounts solidly, comes with all hardware you need plus spares.The riser height is a little non-standard (at 0.88 riser height, you'll wind up at around 2.091 over bore), which will definitely get your head up, but not sky-high like some popular mounts. If you're running an FSB on your barrel (I am), this riser will raise your optic over that without incident.I've been running my optic with full-cowitness directly on the top rail, and I gotta tell you, this riser mount will definitely take some getting used to. On this riser, I've got more of a chin-weld rather than a cheek-weld on the stock. We'll see if I cotton to it, I guess, but if getting your head up off your rifle is your goal, this 0.88 inch mount will do that. The best part is you don't have to spend $150 (or more!) on a branded mount to figure out if you really like your optic mounted way up there. Recommended.
Vi
Reviewed in the United States on December 29, 2024
I mean it works as intended with my other sights. Quality is nice too and feels not cheap. But it wouldn’t fit my vortex UH-1 and I’m a little disappointed as I was looking for a good low profile riser for such a bulky sight. The rail spacing are a little too wide and the base of the mount is too bulky too.
Jarrett Holly
Reviewed in the United States on December 11, 2024
This riser is the perfect height for an EOTech HWS and accompanying G-Series magnifier. Use the included riser block for the magnifier and this Monstrum 0.38” Picatinny riser for a perfect match.
Carl F.
Reviewed in the United States on June 12, 2023
I had a problem with a holographic sight mounted on the picatinny rail machined into the receiver of a modern, higher power air rifle where it was too low. I had to roll my head / cheek down to see it and that prevented a proper shoulder mount and shooting position.This spacer has nicely solved the problem as it raised the sight just right, I can now do a proper cheek weld and not have a hunched posture and when I quickly mount the rifle to my shoulder to the dot is centered and I'm on target.The riser is nicely machined, the edges were deburred and it has a good black mat finish. It fit and tightened up well with no rocking then the holosight fit on top well too. Note that I pushed the riser forward in the picatinny slots, there's slop there then also pushed the holosight forward to take up the space there too. Some people might want an exact spec (tight) Picatinny but I don't have a complaint, I move the different pieces in the direction recoil would take them so it can't move any farther then tighten (and I DO use a 1/4" torque wrench to specs so there's no question of over or under tightening!) and if everything else is correct nothing ever moves.If course only an idiot wouldn't check their zero after removing and replacing sights so it was a pleasant surprise that this riser was was machined true enough that I didn't have to change elevation at all and only windage an inch to be back on target at 85 yards.I sight in at 85 yards so I'm 3" high at 50 yards and 3" low at 100 w/ a 36gr slug @ 960FPS muzzle. For small game and varmint hunting this gives a great 'point blank' sighting method and reduces range estimation errors (without the usual practice of having a 50 yard zero and a lot of drop to estimate at 100)
Nuke Sparky
Reviewed in the United States on March 21, 2023
I had previously bought a mount exactly like this one, made by Phoking. That mount works but, when looking at it from the end, appears to be barely grabbing onto to receiver rail. Didn't really feel solid and, although it has not come off, has always made me nervous. I was recently in need of another short cantilever riser to mount a prism scope a little further to the rear and found this one. I'm very impressed with the fit, finish, and solid feel of this mount. Instead of just the mounting screws indexing into the receiver rail, this mount has three machined blocks that fit snugly into the receiver rail. The clamping plate is thick and solid, fits very well onto the receiver rail, and is secured by three screws. These attributes combine to give the mount a rock-solid feel that I'm sure I'll never have an issue with. Would expect to pay double for this quality. If it only had about 2 more slots, it would be the perfect offset mount!