Your cart is empty.
Your cart is empty.For worn or broken OEM units on most offroad and dual-sport models Made from a nylon fabric composite material Featuring pop out end caps for use with bar end type brand guards All sleeves have molded ridges to secure grips All sleeves come in a 1 piece tube and drum design
WillD
Reviewed in the United States on February 21, 2025
Item seems sturdy. Does not fit 1 inch handlebars and has a threaded end cap. Because it was clearly too small for my project, I did not open to see if there was a way to remove the end cap, but the description said it was possible. 1/4 inch thick "neck" for the throttle cables, push & pull style.
kaelyn Stultz
Reviewed in the United States on September 13, 2024
Didnt fit my 1 inch bars
jacob dixon
Reviewed in the United States on September 10, 2024
Works as it should. Decreases the twist radius
Kody
Reviewed in Canada on July 30, 2024
Fit right and twists smooth!
Jones5000
Reviewed in the United States on May 14, 2024
If you're modding a MT07 this will be the cheapest. Most noticeable difference as far as the bike being more responsive. Let slack out of cable. Install. Take out ALL the slack. Throttle will have no play.Now go take a ride n give her the old rolling throttle blip πππππ
Derek C
Reviewed in the United States on December 7, 2024
Worked perfect and priced fair.
Timothy
Reviewed in the United States on December 6, 2024
No complaints about this at all. Exactly what I needed!
Marcus snodie
Reviewed in the United States on June 16, 2023
Although the install was quick and easy, I could not tell the difference between the stock throttle tube and the aftermarket. This is supposed to be for a r6/r1 with less travel to full throttle but it feels the exact same
Customer
Reviewed in Singapore on January 3, 2021
Quality a bit soft
Steve Engell
Reviewed in Canada on March 6, 2019
Perfect fit on my 2012 Yamaha FZ8. Just had to saw the very end off an 1/8". Very pleased highly recommended. WOT (wide open throttle) in much less twist. Very little play as well. Super easy to install.
Pete
Reviewed in the United States on October 19, 2019
In short, this does work and has the same cam as the KLX250S stock throttle tube. You just need to remove the end cap of this tube to fit it to the stock handlebar and control location. See the pictures.I purchased this to add heated grips on my 2009 KLX250S because it is relatively cheap and I did not want to clean and grind the lip off my stock throttle tube. The cable cam is the same as the stock Kawasaki throttle tube, and tube length is perfect for the stock handlebars and control position. In order to get this tube to work with the stock bars and control location, you must remove the endcap that comes on the tube. The easiest way I found to remove the end cap was to place the tube on the handlebar and slam it down the handlebar so the the end of the bar hits the cap and pops it off. From there, I cleaned the handle bar and sprayed it with some silicone lubricant, whipping off the excess, and positioned the tube and controls to finish the installation. On the stock handlebars, the throttle tube is about 1-2 mm short and the bar does stick out some, so make sure not to fully seat your closed end grips against the end to avoid any issues with the throttle sticking or moving sluggishly. I used open ended Oxford heated grips for my install and glued a home made cap to the ends of them. Use your own judgement when installing your grips, and make sure everything is free moving. I recommend dry fitting and marking fitment locations with a pencil.
Efrain sanchez
Reviewed in Mexico on April 13, 2019
Excelente producto aunque el tiempo de entrega se demorΓ³ demasiado
Roger
Reviewed in the United Kingdom on August 5, 2018
Used on my Yamaha MT07 Tracer , shortens the amount of turn and smooths out the throttle action in my opinion. Well worth the 5 mins to fit.
Recommended Products