Your cart is empty.
Your cart is empty.
Motion Pro carburetor tool 90 degree 1/4" hex driver. This is a 17.5" long 1/4" driver tool with a 90 degree bend on the end so you can reach in and adjust hard to reach adjustment screws on motorcycle carburetors. The specially engineered gear case allows this tool to maintain its small size; necessary for working in tight spaces. In incorporates strong long lasting gears that will provide the torque you need. This is a very versatile tool, it can be used with any 6mm or 1/4" hex bits!
- Precision made of aircraft grade aluminum stainless steel
- Designed for hard-to-reach areas and air/fuel mixture screws on multi-cylinder motorcycles
- Gear driven 1/4 in. hex drive
- Includes five 1/4 in. hex drive bits (all 1/2 in. long) - Straight-slot, Phillips, D-shaped air/fuel mixture screw bit, 6mm hex jet bit 1/4 in.-hex-to-1/4 in.-drive bit
- Can be used with any 1/4 in. or 6mm hex bits
- Max torque is 60 in. lbs.
- 17.5 in. long
- Replaceable drive gears
Motion Pro Part Number: 08-0229
Mike
Reviewed in the United States on June 5, 2024
Made under dash damper relay work assessible, vs taking out the whole dash for one normally unreachable screw!
Joe B
Reviewed in the United States on March 6, 2024
I dont think there is another motorcycle with more carbs than a Valkyrie so you need a good tool to adjust them. After reading reviews, I initially purchased another tool that didnt have exposed gears. That tool may work if you dont have a tight area but for my Valk it did not fit. The low profile of the MotionPro worked great though. I recommend taking out the detent spring and ball but thats person preference.
M Ali
Reviewed in the United States on November 28, 2024
Perfect solution for tight areas. I used it to replace my Prius and Escalade dashboard AC actuators without removing the whole dashboard. With my small hands it works!
David J. Carter
Reviewed in the United States on January 15, 2024
90 degree, compact head width, long reach. This is perfect for that screw (or nut or small hex head screw) that you can see but not reach. Well made tool.
mike wllace
Reviewed in the United States on September 9, 2023
Bevel gears fit and finish are so poor the tool binds and locks up. All the bling of stainless and anodized aluminum mean nothing. The gears are a ruff casting and the out put gear has a riduclous amount of end play. THERE IS NO WAY I CAN HAVE ANY CONFIDENCE WHEN SETTING MIXTURE SCREWS.Waste of money !
john w.
Reviewed in the United States on August 16, 2023
When needed, it saves the day. I work on motorcycles, airplanes, cars. This motorcycle tool isn't well known to aviation people, I've brought it to work occasionally for a tight spot and usually get a comment or two...ooo! Cool, where'd you get that...etc.It is unfortunate that thrust loads on the bits are taken by the bevel gears, forcing them to mesh harder, making for a notch rough feeling. It could be done differently, but that would make the head bulkier, so it's a trade off. I'd probably leave the design as is, and live with it. Or, spiral bevel gears could be used to make it smoother when loaded. But, another trade off- the tool would cost more. Probably a lot more.So, it's pretty good as is.
christopher l brown
Reviewed in the United States on July 10, 2022
This carb tool is very well made and saved me from having to remove the carbs on my goldwing. Its a bit pricey, but is well worth the money just in time saved while also ending carb tuning frustration.
Reviewer
Reviewed in the United States on October 15, 2022
Had a shower drain that had to install from the top and needed a way to turn a sheathed rubber fitting hose clamp screw where no room for hand or regular socket. I used this tool once for $80 and was 100% worth it because a) only tool that worked out of 1/2 dozen ratchet, flex head, flex drill combos and b) if couldn’t use a tool would have spent actual thousands of dollars to access any other way via lower floor cabinetry. Well built tool. Worked like a champ.
Recommended Products