Your cart is empty.
Your cart is empty.Product Description
RATTMMOTOR CNC Spindle Kit 800W:
- 1 x 800W 110V Air-Cooled Spindle Motor ER11
- 1 x 110V or 220V Speed Governor with MACH3
- 1 x 52mm Mount Bracket with Screws
- 2 x Carbon Brush
- 1 Set Drill bits
CNC Router Bits
- Mirror knife sharpening: sharp and clean, smooth excretion, durable.
- High hardness: more wear-resistant than traditional sharp knives, can machine soft metals.
Carbon Brush:
- With External Carbon Brush, it's simple and convenient to install.
Air Cooled Spindle Motor:
- Power: 800W
- Voltage: 110V
- Rotation speed: 5000-20000r/min
- Torque: 0.79NM
- Insulation resistance:>2Megohm
- Dielectric strength: 500V
- Repeat accuracy: 0.01-0.02mm
- Diameter: 52mm
- Total length: 203.5mm
- Axis collet Length: 45mm
Speed Controller Governo:
- Input: AC220V/110V ± 10% 50/60Hz (default)
- Power: 800W
- Output voltage: 0-110V DC
- Current: 6A
- with mach3 function
- Dimensions: 5.51 inches x 4.33 inches x 2.05 inches
Spindle Motor Mount:
- Applicable to:300w 400w 500w spindle motor Diameter: 52mm
- Material: Cast aluminum
- Cast aluminium clamp is much heavier than aluminium profile clamp.
- This product has hardness, strong impact resistance, high hardness and strong antioxidant activity.
Carbon Brush Port
- Equipped with 2 carbon brushes, fully functional and easy to install.
Air Cooling Methods
- This motor has quiet operation, small volume and high speed, and the rear end of the motor is reinforced with a cooling fan, which can be safely worked for a long time.
ER11 Extension Rods and Collet
- The motor is equipped with ER11 extension rod and collet, which supports engraving wood/plastic/acrylic/ pvc/pcb/carbon fiber/density board and other materials.
- Can also be replaced with ER16 extension rods and collets if needed.
- <1> The function of the line is equivalent to a switch, and the output voltage cannot be output when it is disconnected.
- <2> As for the positive and negative wiring of the motor and the power supply, you can connect it at will. Because the motor supports reverse rotation, if you need the motor to rotate forward, just replace the interface.
Note:
This power regulator supports both 110V and 220V, If users need 110V, please just adjust the power supply to 110V.
Tony c
Reviewed in the United States on August 29, 2024
It does not work properly. It comes with a potentiometer that does nothing at all. I turn it all the way down and start it motor starts up when I turn the potentiometer all the way up no change in motor speed the motor only runs at one speed . And there's no paperwork of any kind to help. Poor quality.
Bostontrader
Reviewed in the United States on February 21, 2024
This set is great, but the only downfall is the cooling fan atop the spindle. It' s out of balance and doesn't extend past the OD of the motor, so there is no good airflow and way too much unnecessary vibration. On top of that, the vanes are straight, not curved, so there is no possibility for proper airflow. I 3D printed a new one from Thingiverse and it's much more balanced. Power wise, this thing is a beast. I've cut wood, plastic, aluminum and steel with no issue. Aside from vibration and noise, it's a keeper.
Mike and Kim Mahaffey
Reviewed in the United States on August 3, 2023
Not sure what happened, it got very hot and the sound wasn't good either. Looks like a waste...
Marcos Silva
Reviewed in the United States on August 20, 2023
The first unit I got was bad and after speaking with customer service I got a replacement unit. This unit works well and fit correctly into that CNC.You can cut wood and even metal (do it slowly). It comes with some carving bits to get you started.
FireAtWill
Reviewed in the United States on July 8, 2023
The media could not be loaded.
Hermann
Reviewed in the United States on May 6, 2023
Makes a lot of noise, gets extremely hot even on short jobs (Less than an hour). Pictures and item do not match completely. It works great, much more power than a 500w. O, and the fan feature simply does not cool the thing down. Best to put a normal room fan on it while in operation.
Customer
Reviewed in the United States on November 20, 2022
This thing is poorly packaged, clamp is all banged up and it did not come with the 10pc engraving bits. Also the clamp is way too loose, it just slides right off the spindle. There's no instructions, they should at least mark the positive and negative connections. The power supply was just wrapped in seran wrap.The spindle chuck sticks out too far and doesn't want to budge, it should be pushed in further for better performance. I don't know how anyone is supposed to change the chuck. The chuck needs to be seated further into the shaft, but I don't want to hammer it in. It's a loud spindle for 800w. Louder than my 1200w plunge router. It has small connectors on the spindle. We'll see how it performs.
shaun p.
Reviewed in the United States on October 13, 2022
Instructions are not very clear, you have to supply your own power cord/wires, and the potentiometer not mounted to anything is not the best but definitely a great product for the price. It's not plug and play but when hooked up correctly it works much better then expected.
Recommended Products
$79.00
$ 34 .99 $34.99
$18.00
$ 8 .99 $8.99