Your cart is empty.
Your cart is empty.Product Description
Snorkel intake kit Replacement for toyota 95-04 1st gen tacoma 1996-2002 3rd 4runner v6 3.4L
- Stainless steel ducting and ram head clamps
- Quality UV Stable Rotomoulded LLDPE 1 piece Moulded Body
- Improve airflow into the engine
- Help the engine breathe easier
- Allow cleaner air into the engine
- Raise the air-intake above the water level
- Improve the performance of your 4x4
ONLY Fits 3.4L Engine vehicles and 2.7L vehicles (may require some custom intake tube connections)
Brian Masters
Reviewed in the United States on February 11, 2025
Perfect fitment. Install is straightforward. There is a paper template that is spot on. Simply align it with the fender lines and mark your holes. You need a 3.5" hole for the snorkel. I read a review the rivets in the kit sucked so I didn't even try them (black in my pictures vs silver what I actually used. Note only the early 3rd gen 4runners have the fender tube, if you have a newer 3rd gen you need to buy the oem tube.I had to cut down my cbi ditch light bracket and drill a new hole for the light.
PUBLI MAS
Reviewed in Mexico on September 13, 2023
mi primer opinion la borraron seguro quieren que digamos cosas bonitas cundo no lo es NO RECOMIENDO
Eric
Reviewed in the United States on March 18, 2023
Works well and come with a template
robert
Reviewed in the United States on January 31, 2023
97 4runner. If you have a 4runner, make sure you have the extra tube in the fender, otherwise you need to buy one. All Tacomas have that extra tube and only earlier 4Runners have it. With that said, no instructions are included. Had no idea how the stencil should be mounted. Drilled holes and had to re-drill 2 holes to make it fit properly. The bracket to the windshield frame has too much of a bend on it and made fitment poor. There was no drain for water and that was disappointing. This was a cheap version to a arb model, so I small adjustments will be needed for fitment… but the lack of instructions and where to put the stencil made it a 2 star product. After all said and done, it looks nice and the mistakes are hidden behind the snorkel. I’ll update in a few months with a mention of how it’s working.
Been here awhile
Reviewed in the United States on September 6, 2022
Ebay has 'em cheaper... Fit just fine in the end. It took many times trying to measure, does come with an outline but you will have to use a compass to circle out the intake hole, it just has a small hole but not the whole cutout. Also, the outline kinda sucks but at least gives you an idea. I also recommend that you get the bottom portion done first and then get the mount on the truck for the snorkel itself last. Mine was good but the holes for the top mount were a hair low and I had to finagle it down to get the screws to line up. I also used one of the cheap socks from Amazon to help keep the bugs from going down the pipe, it's working well.
Boosted
Reviewed in the United States on May 7, 2022
Fit on my 2002 4runner great, used a 3” 90 boot and a piece of 3” pipe to connect the snorkel to the intake. Or you can order the Tacoma piece.
Cody
Reviewed in the United States on March 3, 2022
Zero instructions. It would be different if it was self explanatory but where the intake is and where the snorkel aren’t even close
Corey
Reviewed in the United States on March 27, 2022
Fits in the piller have to go to the homedepot to find some parts to finish connecting to air box
Chad
Reviewed in the United States on October 15, 2022
This fit perfectly on my 98 4runner 4x4, drill a 3-1/2in hole and connect it to the factory air box with the included elbow.
Recommended Products
$58.98
$ 25 .99 $25.99
$124.98
$ 61 .99 $61.99
$109.96
$ 45 .99 $45.99