Shopping Cart

Your cart is empty.

Your cart is empty.

Suspension Strut Spreader Tool - Shock Absorber Ram Strut Remover, Ball Joint Spliter

Free shipping on orders over $29.99

$36.39

$ 19 .99 $19.99

In Stock
  • For removal & fitting of suspension struts whilst leaving the hub on the vehicle
  • This Suspension Split Hub Steering Knuckle Spreader designed to allow the suspension split hub to be held open to make the removal and fitting of the suspension strut easier
  • Double ended action allows use on both larger upper split hubs and lower ball joint split joints (Opening capacity:3-10MM, 5-12mm)
  • Features 10MM hex wrench, max. torque 13Nm (hand tool included)
  • Opening capacity: 5-12MM, work on most of vehicle equipped with a pinch bolt style hub, applications work compatible with Audi, BMW, Citroen, Ford, Peugeot, Volkswagen vehicle


The Kauplus Suspension Split Hub Steering Knuckle Spreader For removal and fitting of suspension struts from wheel bearing housing/front axle, also be used on replaced shocks, coil spring. The Shock Absorber Ram Dismantle Separator designed to allow the suspension split hub to be held open to make the removal and fitting of the suspension strut easier, with double ended design allows it to be used on larger upper split hubs together with lower ball joint split hubs without the risk of damage, Use with 10mm hand tools only, MAX torque 13Nm. (hexagonal wrench included). Opening capacity: 5-12mm Keep thread clean & lightly lubricated. The Knuckle Spreader Tool Work on most of vehicle equipped with a pinch bolt style hub, applications work compatible with Audi, BMW, Citroen, Ford, VW, and Peugeot….


Customer
Reviewed in the United States on March 6, 2025
Great
Gabriel Lopez
Reviewed in the United States on September 30, 2024
Great price and it works amazing. This tool is a time saver.
not important
Reviewed in the United States on September 26, 2024
multi functional if you want to spread something metallic and small, if this fits job is done.
Mike
Reviewed in the United States on March 17, 2024
The tool works perfectly as described.
Thomas Herrschaft
Reviewed in the United States on April 8, 2024
A real time and labor saver! Well made tool!
great game.
Reviewed in the United States on April 15, 2024
It works as advertised. I am very happy with it.
KelConquer
Reviewed in the United States on August 24, 2023
I do a lot of work on balljoints and struts/steering knuckles so decided to buy this. I used it on a few Volvos and realized that because the inner edge of the curved section is tapered, it makes the tool want to naturally slide off when it vibrates from hammer impact and whatnot. So you constantly have to pick the tool up from the ground, set it back up, etc. You'll have the same issue if you attempt to over-tighten it, it will just slide right out from the opening. You have to find the "sweet spot" and then it functions very well. I am still giving this a good rating considering the cost of it, functionality, and build quality. The double sided design is a nice touch, and it feels very solid and durable to use. Mine has hit the ground from 4'-5' about 10 times and it's still perfectly usable with no dents or bends. A good addition to the toolbox.
Customer
Reviewed in the United States on March 8, 2023
The bolt used to expand the tool sits too close to the steering knuckle (basically flushed). So, at some point during expansion, there is not enough clearance for the wrench to get on the bolt head. I did use the open end of the wrench at this point, but it was unable to be fully seated on the bolt head due to clearance which increases the risk of stripping. The tool ultimately started to tilt out of position due to the open end of the wrench making some contact with the steering knuckle while turning. After a series of turning and hammering the tool back in place with a 3lb hammer, it did work. If the bolt was a half inch longer or so, it would have been perfect. It seems to be a well-made tool though and it still did make the job easier.
Recommended Products