Shopping Cart

Your cart is empty.

Your cart is empty.

TRANSFER CASE HALF REAR (REINFORCED) - NV 261 HD NP 261 HD NV 263 HD NP 263 HD

Free shipping on orders over $29.99

$129.99

$ 63 .99 $63.99

In Stock
  • National Drivetrain


REAR CASE HALF - HAS TWO THREADED SENSOR HOLES (CAN BE EASILY PLUGGED WITH BOLT IF NECESSARY) - C30605 - REINFORCED AFTERMARKET CASTING ELIMINATES NEED FOR CASE SAVER ACCESSORIES - INCLUDES PRE-INSTALLED TAILSHAFT BUSHING & OUTPUT SHAFT NEEDLE BEARING
CATALOG ILL # 45 - REAR CASE HALF - NV261HD NP261HD NV263HD NP263HD


Me
Reviewed in the United States on March 21, 2025
Installing this on a 2001 2500HD NP263HD transfer case. Everything looked perfect until I noticed the inside diameter of the output shaft seal. The well on this new housing where the rear seal sits measures approximatly 77mm. The bearing seal well from the original case I took off measures approximatly 68mm. This housing may be for a NP263XHD not sure. Returning part. Will update if needed.
Joseph D.
Reviewed in the United States on April 4, 2025
Fits my 2002 Chevy Silverado 2500HD NP263 transfer case. The reason I gave this a 4 out of 5 is because I had to really tap it a few times with a mallet for the bearing with the lock ring to seat into the recess of the case. It’s unlike the original where it easily slides in. It also helps a bit if you rub some transfer case fluid on the bearing and the recess. But yea, overall quality seems to look great. And also, this came with plugs which I didn’t know which is also great.
Ashley W
Reviewed in the United States on August 13, 2022
Fit my 05 NP263HD perfectly. Came with speed sensor plug and one drain/fill plug. Would be nice if it came with the second plug, new snap ring, and output seal, but for the price you get exactly what is advertised. Here’s hoping long term durability is good as well.
david hall
Reviewed in the United States on December 4, 2021
Great value. Haven't had any issues at all after 2 months
Brad
Reviewed in the United States on April 19, 2021
So far so good. It has been about 2 weeks since I made the repairs. No more leaking and worrying about running my case dry. The case mated right up to the front half. All bolt holes etc. we’re properly aligned. I wish the magnesium case would have been priced this way. Now the sad part. I ended up doing this procedure twice because the output shaft bearing was not fully seated in the case. I checked multiple times by prying on the bearing to make sure it did not move. Once in the truck I took it for a test drive and heard a noise coming from the transfer case. Tore it all apart to find that I had to sand the inside of the case half to allow the bearing to fully seat. One thing I would recommend is instructions for this particular area. Other than that I am happy.
Jason Darmody
Reviewed in the United States on June 27, 2019
Didn't have speed sensor hole machines properly
Dan J
Reviewed in the United States on May 24, 2019
Great price and product.
Joni C.
Reviewed in the United States on November 25, 2018
Used this case half to replace my NP263HD. Is aluminum and stronger than original metal, but I added the Merchant Automotive pump upgrade anyway. I read on many other feedbacks people have a hard time getting case to drop over the rear output shaft bearing, some grind it open. Let me explain, the bearing fits very snug by design. An experienced tech would know you gently work the case back and forth to seat bearing. No force is needed, just patients. Once the case half is in, just use a screw driver through the speedo hole to lift the shaft and seat the holding clip. Only other issues with this case half is it comes with two open Speedo sensor holes. One needs to be plugged and you will need to find a plug. Hope helpful.
Recommended Products