Your cart is empty.
Your cart is empty.Daniel
Reviewed in Canada on September 2, 2024
I was very disappointed in this one. It did not fit the Dewalt tool that it listed it fit. The fabrication seems quite flimsy with little spot welds holding it together and the teeth painted over which seems odd for a cutting edge. I tried to return it but they wanted me to pay shipping which was nearly as much as the tool cost so I kept it.
Brian A.
Reviewed in the United States on July 29, 2024
Well painted and pretty looking. That’s about all the positive I can think of.The downside… it was delivered broken and I doubt a replacement would help as the quality of design is exceptionally poor. This was engineered to be as cheaply made as possible without a consideration of what it is intended to be used for. The cutting edges are thin, to the point that during shipping or even prior, they had snapped off in several locations. When not completely snapped off, they are bent enough that during initial use, they would likely break from mechanical stress and strain.If you decide to purchase anyways, I wish you the best of luck and HOPE that you get a refined higher quality tool than what I’d received.
Jim Fleming
Reviewed in the United States on May 5, 2024
These are worthless out of the box... you'll have sharpen the "teeth" to make it effective.
scott
Reviewed in Canada on March 4, 2024
Very cheap, broke 1st time I tried to use it
Client d'
Reviewed in Canada on March 30, 2024
Marche bien
S. Block
Reviewed in the United States on March 21, 2024
These are both the proper size for standard US remodel boxes "old work".They are a very snug fit on my Dewalt DCS356 (and any other dewalt 20v multi tool model. Just make sure the clamp lever is pulled up fully, and snap the blade over the shaft with a little pressure. Check that the blade is lined up with the pins, and that the clamp is fully engaged, and it should last quite a long time.(If it isn't installed correctly, it will bend or break.)I have cut around 30 holes with the single-gang blade, and 12 with the double gang blade. Still sharp and cutting perfectly.
nikki
Reviewed in Canada on February 12, 2024
This would not even cut through a 1/2 inch sheet of drywall. Super disappointed in this item.Used on ceiling tile and the hole was top big for outlet box and the 4 square was top small for 4x4 box
Customer
Reviewed in the United States on February 1, 2024
not as sharp as i thought they would be but worked fine
Fernando
Reviewed in the United States on September 30, 2023
I use the name brand ones and wanted to try these. Put it on my miwaukee fuel and they vibrated very high pitched and ripped off and went flying.
Penn
Reviewed in the United States on September 20, 2023
These are garbage. They dont cut well, and the single gang hole was the size of a wall plate. Every wall ring style I tried was to small for the hole. dont buy.
Sean
Reviewed in the United States on December 28, 2023
I recently added 3 outlets in my garage and since our garage is a finished and insulated garage, I wanted to install the outlets like in the house, within the sheetrock to keep that finished look. After setting up my laser level and with the studs marked with blue painters' tape, I grabbed my DeWalt oscillating tool with this attachment and in seconds had the correct size holes cut into the drywall for installation. Took the outcut piece of drywall out and took with me to Lowe's to have paint matched too. End product came out great. This attachment is well worth it for those of us that aren't drywall guys for sure!
Ron C.
Reviewed in the United States on October 8, 2023
Seriously this this works and cuts like butter! the cuts are super clean! I have tried 4 other brands on amzon and they all sucked. This one is sturdy, the blades DO NOT FLEX like the other ones found on amazon. I have already made over 100 holes with this tool and it still cuts like the first time right out of the box.
Recommended Products