Your cart is empty.
Your cart is empty.Ossa
Reviewed in the United States on January 5, 2025
Para un producto tan sencillo, encontré en Temu el mismo producto a menos de 2 dólares.
Ethan Haueter
Reviewed in the United States on August 16, 2024
It definitely helps with the timing of your shifts, and was a very easy install, but I don’t know if it was worth the money and time. If you are pro racing with paddle shifters it is a very viable option, but for the average sim racer its a bit overkill
NONE
Reviewed in the United States on November 9, 2024
Bought 2 of these and they worked well until they broke. The plastic needs to much thicker.
Elliott
Reviewed in the United States on October 13, 2024
After two months of use, it snapped, making it completely useless. It was great while it lasted, making the paddle shifters not be so floppy. Make of cheap 3d printed plastic that fails on its own. In order to make it work, you have to make it nice and snug so that it won't move and eventually rub against the wheel motor/base.
Na
Reviewed in the United States on September 24, 2023
Ok what’s with all the negative reviews here? This thing is amazing!Shifting is way more on point now! I wish I knew about this sooner!Yes, you can slap this thing on there in a minute, but take your time get it, snug to where it’s tight enough on there to where I can move press it against the paddles toward the paddles on both sides are pressed in. Then move the pedal against the mod just enough to wear it unclicks then tighten it down. You might want to do this on both sides back-and-forth until it’s perfect. That is the key taking your time I spent about 10 minutes on mine to achieve perfection and I’m happy with where it’s at. You can see the pictures how I did mine. There’s only about a centimeter of play when pulling on the far outside edges of the paddles.The difference between moving your fingers an inch verse a half a centimeter makes a huge difference when you are constantly shifting and your shifts must be 100% accurate through corners. The only thing I see about this that could be improved is the fact that the mod is completely flat. I have adjusted mine so it’s so tight that it has just enough room for the paddles to un click with a hair width of space. The travel path has been reduced by almost an inch on the far edge of the paddles. The button itself that clicks and unclicks is very very small and has a mm of range. When it is this snug the magnets are not completely flat against the metal pedal. If it was looser where there would be more play it would sit completely flat against the metal paddles, and touch the magnets better but I am a perfectionist. Even though it isn’t perfectly flush against the metal the way mine is mounted, there is still a pull with the strength of those types of magnets because they are strong man made magnets. Definitely a 5 star review. The tool it came from is perfect for the job and the hardware is amazing too. Not just cheap hardware either it fits very accurately and I love that it’s black Allen head bolts and the nut is good black quality metal as well. The way it’s printed is really impressive too because when you are tightening the bolt through the plastic it isn’t super loose it’s like it’s almost threaded all the way through. Like I keep saying I’m really impressed. If I could change one thing it would be this picture I am going to draw to explain and I am going to take a picture of what mine ended up looking like. Worth the cost in my opinion and I wonder what other mods are out there I could use to improve my set up…BTW people cover your gas break pedals with plastic when not in use because when dust gets in there it will ruin the mechanisms eventually and cause flickering signals and taking this apart sucks! Just a tip so you don’t have to buy another set or clean them over and over and over because taking the pedals apart to clean them means removing over 20 something screws and it is a major hassle. Happy Sim Racing y’all!!!
M. McMahon
Reviewed in the United States on August 8, 2023
If snugged up just right (see pictures)…this mod will reduce shifter paddle travel, resulting in quicker, less flappy shifting. Nice quality parts. (if the screws were a little longer, it would be easier to install)Will it make any difference in driving performance??? I’m not sure yet, it certainly can’t hurt. It DOES make shifting feel quicker and much more substantial, resulting in a solid, satisfying, sounding shift.Bottom line….tactilely shifts better, better sounding, less flappy. That adds value alone for me.
marty walters
Reviewed in the United States on June 25, 2023
Very very quick install I don't know if I did it right but it works great and it got ninja skills it hides in the shadows
Daniel yeh
Reviewed in Canada on December 26, 2023
Product came rusted on the hardware not a huge deal. Used the product one and notice it got loose, Checked and noticed it was cracked. This wasn’t cheap so it was upsetting seeing this not lasting.
J
Reviewed in Canada on October 9, 2023
Works great for a few hours, but broke suddenly during a race. I was cautious to tighten it anymore than I did — but it still broke.Made sure to avoid over-tightening as it does create stress on the part. But any looser and it would fall off or stick to the paddleshift.
Pedro
Reviewed in Canada on October 30, 2023
Not a good fit for G920 as it is too fragile for the spring force of the steering wheel paddles and will eventually break.
Clifford B
Reviewed in the United States on November 19, 2022
Installation is straightforward- but after testing this product on my G923 wheel for several hours, I concluded the difference was imperceptible for me, and immediately after removing it I realized I actually preferred the action of the shifter paddles without it.
Recommended Products