Your cart is empty.
Your cart is empty.Product Description
rolanda
Reviewed in the United States on March 18, 2025
I do resin crafts for different vending events, and I wanted to try to do some bracelets. I love the way everything came out. the skinny bracelets you do need like a syringe or something small to put the resin in. I did make a mess but the bracelets come out beautifully. Everything was easy to use and the bracelets are so cute.
Two Crazy Shuckers
Reviewed in the United States on February 25, 2025
Exactly as pictured!! Great group of molds for the price .. the size variety is great!!
Iva Lynn Myatt
Reviewed in the United States on April 2, 2025
Good quality.
Sofia C.
Reviewed in Mexico on August 6, 2024
Está bueno para lo que lo necesito
Sara Brunk
Reviewed in the United States on June 11, 2024
Awesome molds love them will save money . They were exactly as advertised
Linda
Reviewed in the United States on May 14, 2024
I’m brand new to this resin jewelry making, and have only tried a couple of these so far. They arrived straight, no warping, and the bangles were easy to unmold. I am not good at filling the molds yet, and the outer edge was rough and flat. But once unmolded, I ran a small bead of clear resin over that rough edge and cured under the lamp and it turned out great! I’m sure with more practice it will be even better! Great price for as many different molds you get in the pack.
PDS
Reviewed in Canada on March 7, 2024
This is my second set of these molds. They are fantastic. They release well, both the mold and the surrounding top face (which seems to stick like super glue on a lot of other ring molds), they are very thick and sturdy (probably twice as thick as most of my other ring molds) and they have a good selection of sizes without going too crazy (not going to fit every finger on every hand but probably at least one finger on every hand).These are however not meant to be popped out of the mold and put on your finger, they are way to bug for that. These are excessively long and wide blanks so you can sand and carve them down to a multitude of custom shapes and styles. If you don’t have the machinery required to do that, this probably isn’t the mold for you. If you do, these provide near limitless possibilities for customization.Highly recommend.
SarahDJ
Reviewed in the United States on March 4, 2024
For the money, these molds are a hit.I was a bit concerned about the sizing but not anymore this was a great buy, two molds for one price.What i did was resin each ring so that i know which size is which and the samples are sizers that can i use to size other peoples fingers.My other advice is when you place your resin in the ring mold and under the UV resin lamp for 5-10 mins to cure. Once the lamp light is off, make sure to let the resin rest in the mold for an additional 5 mins before taking it out of the mold. Just to ensure that the resin is dried and fully cured. Hope this helps!
Erin M
Reviewed in the United States on December 20, 2024
First, this arrived 2 days late.They,are pretty small, as I love bracelets I chose
A reader, a crafter, a gardener and cook
Reviewed in the United States on November 23, 2021
This is an decent set of bracelet molds but there are a few issues.As you can see in my photo, one of the bangles is so small I can't even get my hand into it, while another is so large it goes up to my elbow. When I poured the larger one, I discovered it's so large that it can't be worn....it falls right off my arm/hand. I tried putting it on first, and then the smaller ones hoping they would prevent it from falling off and it was iffy. It will slide right over the top of the smaller one and off my arm so I had to remember to stack in a specific order. I didn't like that so stopped using that bangle entirely. That meant that 2 of the four were not usable.The way the molds are shaped, the edge of the bangles that is inside the mold comes out with a rounded edge. But the edge that is open/top comes out with a flat edge. I tried adding more resin in an attempt to get that edge rounded but it just spills out and leaves rough edges which need to be sanded.I don't like that you can't get a rounded edge on both sides. I have a mold for a sphere which is basically enclosed with a pour spot so you get a true sphere. I'd like to see a bangle mold like that so that both edges will be rounded.The C cuff one worked great as both ends are flat. The O cuff is a bit small but I could still get it on/off.I used epoxy resin, not UV, in mine. They unmolded easily.
Recommended Products