Your cart is empty.
Your cart is empty. The Haoge Lens Hood is primarily designed to prevent unwanted stray light from entering the lens by extending and shading the end of the lens, plus prevent vignetting. In addition, since the end of the lens is extended, you also get the added benefit of some extra protection from accidental impact.
Specification:
Bayonet mount design
Material: Plastic
Color: Black as Photo
Replaces Nikon HB-40
Compatible with:
Nikon Nikkor AF-S 24-70mm f/2.8G ED N
NOTE: Only compatible with the lens list above. Please verify your lens model before order.
Package Included:
1 x Haoge Lens Hood
Holley Blackwell
Reviewed in the United States on June 9, 2024
Cheap plastic replacement piece but it does the job! It fits perfect on my 24-70mm and is sturdy!
Joe C.
Reviewed in the United States on October 24, 2024
Works as promised for a Nikon lens.
BH
Reviewed in the United States on September 21, 2023
I'm a professional photographer with 30 years of experience. This replaced the original lens hood (HB-40) on my Nikon 24-70mm f2.8.THE GOOD:- I got it onto the lens, and it does its job.- The hood was not visible throughout the 24-70mm range.- The finish is the same black "orange peal overspray" as the Nikon bodies.THE BAD:- The threads on the original HB-40 are metal and easily screwed on and off the lens while still fitting snuggly. These threads are plastic and are REALLY tight. After carefully screwing it onto the lens once, I removed it and looked at the threads, wondering if something was wrong with them that it was so difficult to screw on. What I saw concerned me. After installing it only once, there were already visible wear marks on the inside of the rings. Common sense says, "It'll loosen up with time." But that's the point. It shouldn't have to wear out to fit correctly.CONCLUSION:If you lost the original lens hood and need one like me, this is a cheap and adequate solution.I don't expect it to last more than a year, but it'll do for less than 15 bucks.
Joseph D. Land
Reviewed in the United States on August 20, 2022
It works, but it's so tight that I'm worried I might be damaging the plastic rim on my lens with this. It's for a f2.8 24-70 F mount. Not sure If I'm going to keep using this
Bogdan Radu
Reviewed in Canada on January 7, 2021
This hood has a slightly rougher texture than the original Nikon but works just as well. If anything, this texture makes stray light scatter better. It also fits just as well as the Nikon original hood.It’s a good replacement I can recommend without reservations.
greg perks
Reviewed in Canada on September 30, 2020
This lens hood is a very solid build quality. Doesn't seem like cheap plastic at all. The click of the lock is very solid and doesn't move or is flimsy in anyway. The only small problem I had was a few small burs that where on the inside that would have rubbed against the lens. A quick clean with the sharp knife, and that fixed it right up. You can see in the attached first picture. Overall very happy with this.
Kelly C
Reviewed in the United States on September 19, 2020
Perfect! My original hood broke. This was an awesome replacement. Fits great and does it’s job. Don’t know what else I need in a lens hood!
Carla Corey
Reviewed in the United States on July 1, 2020
Time will tell. It fits like the Nikon brand. However the difference is Nikon uses a metal locking latch. Will the latch fail prior to something more catastrophic, the original lasted 15 or so years, not sure this latch will last that long.
EFJ
Reviewed in the United States on June 21, 2019
It’s fine, works as the original
E. Bishop
Reviewed in the United States on March 18, 2019
A little more study than original! Excellent!!
Recommended Products
