Your cart is empty.
Your cart is empty.Idaho's sliding door combination pulls (25410, 25411) in passage and privacy functions have been the industry standard for many years - easy to install and fully reversible. Since 1987, idh has been supplying a wide spectrum of high quality solid brass architectural and decorative hardware and bath accessories to our customers nationwide and abroad. Our products are strategically positioned to appeal to pro-customers who demand elegance in solid brass at great prices.
LaicieDaze
Reviewed in Australia on March 18, 2025
Great quality, nice colour and a reasonable price. Shipping was fast too. Exactly what I was looking for.
F. Rossi
Reviewed in the United States on April 7, 2025
I needed to replace an existing pocket door latch that was painted over and beat up. Door notch was already cut to the same dimensions, so it was an easy replacement. Swapping out the new latch took a few minutes and looks 100% better.
Kelsey Rowe
Reviewed in Canada on July 28, 2024
Watched a youtube video on how to install it in a door. Obviously, I needed some tools from the store to cut the hole, but if you already have a hole, this is super easy to install!
Romanceismymiddlename
Reviewed in the United States on June 10, 2024
This product looks like what I ordered, but the quality is not a good as I had hope. The finger well is very shallow and makes pulling the door shut at the last cm very tough (I use the hook on the inside of the hardware to pull it the majority of the way). The thumb turn to lock it is also wiggly and loose. Just doesn't feel newly installed or sturdy.
Placeholder
Reviewed in the United States on May 22, 2024
This was a perfect fit and very easy to install
Kindle Customer
Reviewed in the United States on May 18, 2024
This works fine, but pay attention to the directions, and don't cut the door any bigger than necessary. And the general problem (as I've learned from others) is that the little locking handle/knob is hard to do, the sloping edges don't give enough grip to push the door the last two inches to close, and the locking know is too close to the door frame. But these problems are common to _all_ standard mechanisms so I can not fault this device.A friend suggested that I cut a finger grip into the door a couple of inches from the edge. That's on my list of things to do.
Bill Schreiber
Reviewed in the United States on April 3, 2024
Fit perfectly. Looks great. Wife happy. HAPPY WIFE; HAPPY LIFE!!!
Jeff Angold
Reviewed in the United States on March 30, 2023
Good quality for sure. Easy to install if you are replacing an old one
Manjait S Dhoot
Reviewed in Canada on February 26, 2023
Installed in minutes. Good quality Product thats looks brilliant.Very happy with the purchase and price.
John S
Reviewed in the United States on September 13, 2022
Good quality. First, the specified cutout needs to be precise, very square and true to the surface of the door. The cutout creates the recess that the leading edge of the lock fits into the door. Also, need to drill out a hole in the back of the cutout for the locking mechanism to move. Use the same 15/16 bit and drill it about 1/2". Lock should move ok. Don't forget to loosen the two phillips screws. This allows the assembly to expand to fit your door. Then tighten when finished. The door must fit very flush with the jamb when closed. Otherwise lock will not catch in the latch plate. The latch plate requires careful positioning. Good luck but a very nice product after it is installed.
Philip
Reviewed in Australia on May 30, 2021
Didn’t come with faceplate for frame
Michael on Vancouver Island
Reviewed in Canada on October 24, 2019
Good quality for the price. Paid $11 CDN for it summer 2019. Purchased the oiled bronze finish model to match the existing house hardware and it's a good match.Only reason for not giving 5 stars is the instructions should have suggested pre-drilling the screw holes, as the screws are quite soft and subject to round out and scar the finish as I did with one you can see in the picture. Other than that, the instructions were easy to follow and installation was completed in about half an hour. I should mention the instructions we're a bit on the small font size. The height of the hole you have to cut is 2 & 1/4 inches and the depth is 1 & 3/4 of an inch.
R. Carlson
Reviewed in the United States on September 15, 2017
Good quality replacement for older pocket door hardware. They did require a bit of fiddling to make the locks work. Eventually we just gave up since no one in our house uses the pocket door locks.Pros:Pretty much plug compatible with the 20 year old units we removedLook greatCons:Could not get the lock to work consistently
Recommended Products
$5.68
$ 2 .99 $2.99