Your cart is empty.
Your cart is empty.Backed by superior materials and rigorous testing, MOOG® control arm bushings deliver reliable performance you can count on. MOOG problem-solving innovations ensure fast, hassle-free installation.
Mike Calimari
Reviewed in the United States on January 26, 2025
The Moog box looked like it wasn't opened tho there was no tape seal the flaps looked good.The inside and bushings were a different story as they were filthy.The bushings showed no signs of an attempted installation but other brands come clean and bagged.The rubber insert has Mexico and Clevite molded in so they are probably genuine, I think.Waiting for a reply from brandprotection@driv.com before returning.
Kindle Customer
Reviewed in the United States on September 24, 2024
Easy to press on
KJ10470
Reviewed in the United States on February 23, 2024
Fit both axle bushings for my 2004 Jeep Grand Cherokee WJ. Not easy to remove the old ones, even with an air hammer, but VERY easy to install with an auto store rental press, especially after freezing the bushings for a few days
Josh
Reviewed in the United States on November 5, 2024
Replaced the factory ones after 30 year and they're working great a year later.
Brad
Reviewed in Canada on April 2, 2024
Took some digging for part numbers but contrary to Amazon they do fit a 2002 jeep grand Cherokee upper control and upper axle side bushing.Local parts houses couldn’t find a listing but Amazon had it on my door step in 3 days.
W. Wells
Reviewed in the United States on December 31, 2023
Moog is a very good brand, so when we were replacing the front, upper control arms on our WJ, we searched around and figured out that this part, the K3166, is what we needed to finish the job. Installation is easy if you borrow a ball joint press from your local auto parts store. I will say that removal of the old, worn out bushings was not a lot of fun. They did not want to let go. A friend later told me I should have heated them up with a torch first, then beat them out. If there's a next time, I'll try that.
Sven Meyers
Reviewed in the United States on July 30, 2022
Like the OEM. Fits for the axle side of a Dana 30. Tough getting old out and new in but that’s what you want. Don’t want these slipping around.
Quinten Kandt
Reviewed in the United States on March 19, 2018
I installed these in a 2002 grand Cherokee with the Dana 30. fit great. I had to rent a ball joint press to press them into the axel. comes as a set of two, I bought new arms for the uppers. they work and fit as expected. don't think I would have done anything different. I know the MOOG website says they don't fit, they are a like and kind replacement for the stock part. I had the same concerns as everyone else about buying them since the vehicle isn't listed. no issues whats so ever with the install.
Rory
Reviewed in Canada on July 19, 2017
Worked great
thomas
Reviewed in Canada on October 20, 2017
good product really good price
Brian A.
Reviewed in the United States on April 13, 2017
First off, the Amazon “does this part fit your car?” is wrong for the 1999-2004 Jeep Grand Cherokee (WJ). These (K3166) are the correct bushings for the upper control arms for the front axle. Each package contains two bushings, so you will need two boxes to do all four uppers. They are the same front/rear and left/right. The body side can be done with a shop press or hand press as the arm comes out when unbolted. The axle side bushings are more difficult as they are pressed into the axle and not the arm. A hand press (4WD service kit) will make life easier, but I found that an air hammer popped them out in about 2 minutes each. It’s important to remember to not torque down the bolts until the car is sitting on its own wheels. If the bushings are torqued before the suspension is loaded the bushings will be under a twisted load and fail prematurely.I’ve used Moog components and never had an issue and I’m hoping that these will have the same result. I am however removing one star because these bushing are clearly marked as Clevite and not Moog. There is nothing inherently bad with Clevite bushings, but they were sold in Moog boxes as Moog.After installation by front end ‘clunk’ is gone and two bad bushings were clearly the culprit (see picture)!
Recommended Products
