Shopping Cart

Your cart is empty.

Your cart is empty.

Muffler For Snapper Repl Snapper 7074453

Free shipping on orders over $29.99

$53.18

$ 23 .99 $23.99

In Stock

About this item

  • Replaces: SNAPPER/KEES: 7-4453, 7074453, 7074453YP, 74453


Muffler replaces Snapper 7074453. Used on OHV single cylinder Briggs & Stratton engines on rear engine riders.


m kresko
Reviewed in the United States on March 9, 2025
Perfect fit
Nick
Reviewed in the United States on September 16, 2024
Easy bolt on muffler. Seems to be good quality.
Bigh
Reviewed in the United States on June 10, 2024
Well made and finished, though mine came a bit dented on the heat shield and the pipe. I will do worse to it I'm sure. Perfect replacement for the '91 era Snapper RER mower (3314 model) that was recently given to me. You'll need a gasket, and by my measurements this is the one you'll need:https://www.amazon.com/gp/product/B0B1PJD83G/ref=ppx_yo_dt_b_asin_title_o00_s01?ie=UTF8&psc=1I have yet to receive the gasket and will report if it's wrong, but you'll have six that will likely last you for longer than your memory. Or you can have a muffler party down at the pool with your five Snapper friends. They make lousy coasters, so I honestly don't know why I need six.
Customer
Reviewed in the United States on May 28, 2024
My local shop wanted $180 just for the muffler, I got it online for $60. Same muffler.
cabbo800
Reviewed in the United States on May 12, 2021
Fit like a glove. High quality with easy hookup and soft sound.
John A. Sandoval
Reviewed in the United States on August 5, 2020
Fits 7800786 series Snapper. If your mower is on the older side and has been out of doors you will most likely need a new gasket and bolts.Briggs and Stratton 7015352SM Gasket, Exhaust .Two Socket Head Cap Screws, Hex (Allen) Drive, 5/16 in-18 X 3/4 inNote: My cap screws were buggered from rust so I had to cut a slot in the cap and use a large screw driver to work it out after 24 hours of PB Blaster penetrating oil.)
bikester
Reviewed in the United States on June 19, 2019
This worked great for my Snapper rear engine rider - series 5 (1980's vintage) project. I installed a new Briggs and Stratton 11.5 hp Intek 21R807-0072-G1 engine. The muffler that comes with the new engine will not clear the tractor stand-up pipes in the rear. You need this muffler to nicely finish off the retrofit. The new engine is now much quieter than the original Briggs 8 HP.
Gary K
Reviewed in the United States on June 22, 2013
Purchased this muffler (http://www.amazon.com/gp/product/B0097C27JE/ref=cm_cr_rev_prod_title) to replace the rusted out one on my Snapper 11.5 HP rear engine rider, and it was a perfect fit. Quite a bit quieter than the rusted out one was. I was worried about getting the old bolts out, but I sprayed them with PB Blaster and gave it a shot a couple of hours later, and they weren't too difficult to remove. I used a pliers to get extra torque on the allen/hex head bolts.Note that this muffler does not come with a new gasket or bolts, so be sure to keep the old ones! The original OEM gasket is metal, so it's easily reused if you don't break or bend it. I think it's a bit pricy, but it appears to be OEM, so it should last at least as long as the original.