Your cart is empty.
Your cart is empty.Product Description
PARTSam Double Led Trailer Tail Lights
This light is designed for surface mount installation and has a slim profile, making it an ideal choice for the back of your trailer, RV, camper, or motorhome.
IP65 Waterproof
- Free to use in heavy rain, this product helps keep your vehicle well-marked and ensures safety.
- Its epoxy-encapsulated electronics prevent damage from water and corrosion.
Package Content
- 2pcs double led trailer lights 33LEDs including screws and foam gaskets (as shown in the picture)
shan terrazas
Reviewed in the United States on January 18, 2025
Perfect fir for jayco redhawk. Looks great and brighter than original if your undecided and your read this click buy now
Ty W.
Reviewed in the United States on August 23, 2024
These works so well. They fit the original holes. Seals are good but I still added caulk to it. They look so good and for the price you can’t beat it. They are way brighter than the factory
Jerry W
Reviewed in Canada on July 29, 2024
Manufacturer should add that if your are replacing filament style lights you will require resistors to stop hyper flashing.
The Egyptian Car Tech
Reviewed in the United States on June 3, 2024
The assemblies truly brought my old 1980s cargo trailer to the 21st century. The trailer looks much more modern. The lights were very easy to install they fit much better than the old halogen assembly I had. The wiring was very straight forward. The lights are very BRIGHT 🌞. The screws provided for installation provide a very durable finish that is water and weather proof.
R M.
Reviewed in Canada on June 27, 2024
These Lights were an exact match to the old units i was replacing on my rv… the screw holes were even the same.. once I sorted the wires out and connected everything…I soldered and used heat shrink tube for a solid long lasting install.. they are bright, and very clear.. good choice for someone with a little wiring ability (low voltage) and some simple hand tools….
SC-Surfer
Reviewed in the United States on February 22, 2024
These lights were a perfect fit for the early 2000s vintage lights on my Arctic Fox 990. Wiring them up was straight forward. Only detail to keep in mind is that they have 2 ground wired instead of the 1 the older lights have. No big deal. Just connect both white wires with the single ground on your rig.Screw holes lined up perfectly and I needed only a screw driver for install.They are much brighter than the old incandescent lights they are replacing. The old ones were so dim I worried about others seeing my brake lights during the day. These will be much safer.They're pretty cheap and made in china so we'll see how long they last. I will update this review if I have any issues.
Mark Terry
Reviewed in Canada on December 24, 2024
Quick delivery at a decent price
David E.
Reviewed in the United States on October 26, 2024
Easy to install. So much better than the original lights.
Cody
Reviewed in the United States on October 1, 2024
The media could not be loaded.
MurrayFyfe
Reviewed in Canada on September 1, 2023
Direct fit on 89 motor home, easy installation, nice an bright ,priced reasonably very satisfied
The RV DIY Guy
Reviewed in the United States on July 20, 2023
I have learned in the installation. That if you have not had LEDs on your RV, there are a few things that NEED to be addressed. 1. Fast blinking is very possible in RV's under 1999. If using these rear lights. You should also replace the 2 front blinker bulbs with LEDs that work for your vehicle. Then buy an Adjustable LED blinker switch that works with your vehicle. Then replace the old switch with the new Adjustable switch. Put another one of your vehicles in front of the one you are adjusting. Turn on the blinker of the other vehicle. Then turn the knob on the adjustable switch until they match as best as possible. It is so much easier than having to install resistors in the circuit of the blinking lights. The resistors do heat up if used for too long a time. If you have a wooden underlayment as do most older RV's. This could become a FIRE HAZARD. Plus the ADJUSTABLE switch was so much easier and cheaper to do. No Mechanic is needed. Plus this installation was so much SAFER. Now I have very visible lighting that everyone can see.Thank you for making this lighting kit. It fits perfectly where my originals were. Right down to the screw holes.Well a few months later and finding out I had NO CRUISE CONTROL. I had to install resistors in a safe place that would resist heat the best. Now I have my Cruise Control back and no back lighting when the engine runs. The lights work as they should and so does my cruise control. See the pictures. The resistors stay much cooler in the are I installed them in. They are way up under the rear deck bottom of the storage and the shower. They are Formula J87 make 50W 6 Ohm. By Automotive Lighting.
Michelle R Lemoing
Reviewed in Canada on June 22, 2023
I read the reviews before buying these and I have to admit that I was a bit skeptical. Turns out they are a perfect replacement for the older Bargman incandescent tail lights. Even the screw holes match! The other worry I had was that these new led lights from Partsam would hyperflash, but they do not! Another bonus! We were so impressed with these lights that, two things, I decided to write a review, which I hardly do, and we decided to replace all of our marker lights with the same Partsam brand. Extremely happy so far!!
AussieTX
Reviewed in the United States on November 2, 2022
The original 2007 Winnebago tail light assembly was aging and the seals were cracking and a lot of condensation forming on the inside. Not to mention the older incandescent bulbs which were giving me trouble with poor connections and having to constantly clean them with emery cloth and dielectric grease. I also never liked the way the originals stick out over 2.5 inches from the body.The original fittings were 9 X 9 inches and these new LED Partsam lights were the closest in size I could find (9 x 7). This meant 2 of the mounting holes from the original lights would be covered but two would be exposed. Filled the old exposed holes with silicone and then used a push in plastic plug so not a perfect install but I'm more concerned that those behind me can see my lights, breaks and my indications to turn.Wiring was very simple and my rig is built on a Cheve Express chassis with a solid state flasher unit that supports LED indicators so all works great.I have only tested in the day light and can see these are at least twice as bright as the old. Very happy!Lights do come with a large black foam gasket but I also added a bead of silicone around both sides and the top to ensure no moisture gets in. Recommended!! Hopefully they will continue to shine bright for many years to come.
Recommended Products
$22.99
$ 10 .99 $10.99