Your cart is empty.
Your cart is empty.Paul Yaffe says, "Give instant attitude to your Bagger with a fresh new set of ape hangers!" Mandrel-bent from 1" seamless steel tubing and then treated to a chrome bath or gloss black powder coat. Notched for electronic throttle. Knurled, dimpled and pre-drilled for internal wiring. Available in 10", 12", 14" and 16" heights. Made in the U.S.A. NOTE: Bars listed for 94-16 FLHR/FLTR will also fit most 84-16 models with 31/2" on-center risers (except Springers, FLT/FLHT and XL 883C/1200C models). NOTE: When installing any of these bars on 2007 and earlier models, the one-piece top handlebar riser clamp OEM #55918-08 (or PART #0603-0363) MUST be used.
Cory
Reviewed in the United States on June 22, 2024
Good product for the price. Look good and feel good. Would suggest going with longer throttle and brake cables if getting 12” bars but they still work
Kenneth Smith
Reviewed in the United States on June 22, 2024
Turns out I already had 12’s. When I purchased them, they were supposed to be 10’s. When I received the new bats I ordered, I realized they were exactly the same as what I had already.
Richard Todd
Reviewed in the United States on March 31, 2024
I bought these 1inch bars to replace the 1 1/4 inch bars I previously installed on my 2014 Ultra that had a cracked weld. Being 1inch there are no welds to crack. However being 1 inch makes the install more difficult. During the install one if my heated grip plugs was damaged because the holes in the bars are just barely large enough for the plugs to get through and when you wrap them in tape they are very tight.The install was a total pain but the bars work as advertised and have the stock look I was going for.If I ever do a bar change again I will go with the 1 1/4 inch bars to make the install a little easier. But I pray I never have to change these bars again.
Tony F.
Reviewed in the United States on April 9, 2024
Fit good and look good
brandon bartlett
Reviewed in the United States on April 1, 2024
These were the perfect addition to my Yamaha Royal Star Venture.
David
Reviewed in the United States on May 21, 2023
I recently installed these handlebars on my 2002 Harley Electra Glide, and they have been an absolute game-changer. The installation process was a breeze, and they fit perfectly on my bike. Not only do they work flawlessly, but they have also significantly improved the comfort of my rides. The vibrations and bumps are noticeably reduced, providing a smoother and more enjoyable experience. These handlebars have truly transformed my riding experience, and I highly recommend them to any Harley Electra Glide owner looking for an upgrade.
Joseph Dawson
Reviewed in the United States on October 13, 2022
I purchased and installed these bars the week before our 3,000 mile trip. I had ridden bikes with 12" bars, so I was pretty sure these were the right height, and I didn't want to have to buy new cables and brake lines. I am 5'-7" tall, and I put these on a 2013 Harley Davidson Electra glide classic. ( FLHTC ) . The installation was not to bad. Probably a 3 out of 5. ( If you have some experience working on bikes. ). You can use your stock cables and brake lines, they have to be rerouted from the original position. The holes in the bars have a ridge on them that should be ground down as not to damage the wiresThe ride was without a doubt the most comfortable ride I have had on this bike, I wish I had done this many miles ago.
Sherry Gourdin
Reviewed in the United States on July 10, 2021
Easy install, looks great, amazing to ride with!
Recommended Products
$42.44
$ 21 .99 $21.99