Shopping Cart

Your cart is empty.

Your cart is empty.

Seachoice Universal Boat Kill Switch Kit,Red

Free shipping on orders over $29.99

$15.39

$ 5 .99 $5.99

In Stock

About this item

  • Kit includes switch, 50-inch coiled lanyard and disconnect clip
  • Universal fit
  • Black nylon casing
  • Rating: 5A at 12V
  • Protective clear package for easy visability and application
  • Manufacturer part number 50-11681


The presence of a reliable kill switch is essential in providing a safe platform. Designed as a fail-safe to prevent a runaway vessel in the event the operator falls overboard, a quick pull on the lanyard stops the engine. Kit includes switch, 50-inch coiled lanyard and disconnect clip. Seachoice is committed to delivering quality marine accessories and OEM replacement parts to satisfy fishing, boating and watersports enthusiasts worldwide. Seachoice is run for and by boaters offering a wide-ranging product line while remaining affordable.


DAN E BEDENBAUGH
Reviewed in the United States on September 11, 2024
Easy to install. Worked great.
Vinnie
Reviewed in the United States on May 22, 2024
Installed the switch on my old town kayak. Woked when tested before and after install , have not actually had to use it as no falling oit of kayak yet 😅Would definitely buy again
Eroc
Reviewed in the United States on November 7, 2024
Works as it should.Allows for wiring to be normally open circuit or normally closed circuit.
Pedro raad
Reviewed in the United States on November 28, 2024
Espectacular
cici
Reviewed in Canada on September 14, 2023
No complains
S. Miller
Reviewed in the United States on June 14, 2023
I have no experance hooking one of these up. I was able to do it in about 2hours after reading direstions, watching youtube videos. It works likes it's supose to. the quality is good, seems like it will last a few years.
Ed W
Reviewed in the United States on May 8, 2021
Needed a kill switch for my optimax outboard did want to pay manufacturers price this switch was easy to install and the price was great would recommend it.
Pablo
Reviewed in Spain on January 4, 2021
Ok
Carine et Flo
Reviewed in France on September 30, 2019
J'ai acheté ce Coupe circuit pour un Yamaha R6 de 2008. Le prix est très concurrentiel par rapport aux produits dédiés moto.Il est très simple à monter et fonctionne parfaitement. Je recommande. q
FrancisHGC
Reviewed in France on September 11, 2019
Répond au service attendu
UpNorth
Reviewed in the United States on June 24, 2019
I bought this out of desperation - a factory replacement switch that's an actual Mercury kill switch is listed at over $50, and labor to install was $80/hour....for a painfully simple switch, and install. That's just dumb. I'm relatively mechanically capable, so I found this on line, it arrived within a few days, and installed relatively easy with the 9.8 Mercury 110 (model) when it was still hanging on the boat. The only difficult part was to ensure the (single) wire from the engine crank (energized "mag" wire) was placed onto the correct post on the switch, and because the old Merc used the old switch design as the "ground", I had to make a short "ground jumper" to add to the switch and then simply screw it into an existing screw located on the engine cowling so a ground was in place for the switch to work. Bottom line = great switch so far. Relatively easy to install. 1/10th the price of having someone else do it at a real shop. Good stuff.
javi
Reviewed in Spain on November 24, 2018
Perfecto funcionamiento y gran rapidez de entrega lo recomiendo 100%
R. S. McGowan
Reviewed in the United States on June 1, 2011
no instructions are included. Instructions below are lifted from:[...]I used a female connector rather than male."If your motor already has a push button kill switch to stop the motor, then half the work is done for you. All you need to do is cut the wires behind the switch and remove it. You'll then need to strip a bit of insulation off of the tip of each wire and then install a male adapter on each tip. You can then install the kill switch. It should fit right in the old hole with little or know modification. Then just attach the wires on the C-posts on the back of the switch and that's it. From then on, you should be able to push the red button with the lanyard in to kill the motor just like the old push button kill switch, and/or you can yank out the lanyard to kill the motor."I should have installed this year's ago. I can't tell you how well this product holds up, but it arrived very quickly, was easy to install (w/ above instructions), and passed my initial testing.
Recommended Products

$174.50

$ 68 .99 $68.99

4.6
Select Option

$86.53

$ 42 .99 $42.99

5.0
Select Option

$80.99

$ 37 .99 $37.99

4.3
Select Option

$65.62

$ 26 .99 $26.99

4.7
Select Option

$12.23

$ 5 .99 $5.99

4.9
Select Option

$30.83

$ 14 .99 $14.99

4.6
Select Option