Shopping Cart

Your cart is empty.

Your cart is empty.

TeraFlex 2610000 Exhaust Spacer (Jeep JK)

Free shipping on orders over $29.99

$61.43

$ 24 .99 $24.99

In Stock

About this item

  • Bolt on installation
  • For 2012+ JK Wranglers
  • Prevents contact between front driveshaft and exhaust cross pipe
  • Fit type: Vehicle Specific


The TeraFlex exhaust spacer kit needed for all 2012+ model JK Wranglers using a lift kit with 2.5" or more lift. The spacers are installed between the driver and passenger head pipe flanges and the flanges of the cross pipe, which move the exhaust cross pipe rearward


Anthony Drossart
Reviewed in the United States on July 31, 2024
Bought my jeep lifted and the used another brand and the bolts were good long. I would strongly recommend this product.
Customer
Reviewed in the United States on June 18, 2024
Pay the extra cash for this. Well made. Solid steel construction not that stamped crap. No bolt length issues like other brands.
Shawna Shannon Adams
Reviewed in the United States on September 4, 2023
Super disappointed in the quality! I get to figure out how to drill this bolt out and make it work somehow. Thanks for your poor quality and wastingmy time.
Bob
Reviewed in Canada on January 24, 2023
Very nice fit good, paid more than you would for other brands but the cheaper one looked like they would choke off the exhaust gases a little . I planned on keeping this jeep so paid the extra $
Justin
Reviewed in the United States on June 9, 2020
Absolutely simple to install, dropped the exhaust down off of my front driveshaft like magic. Watch your clearance further back if you don’t cut the index pin off like the install video shows.
Paul
Reviewed in Canada on December 11, 2018
Work as described! But trying to install them is a pain in the butt due to the Jeep exhaust bolt location Design. Also note after installing the exhaust may touch and vibrate against the cross member below it upon acceleration. It's as easy fix just add a couple of thick washers between the 2 cross members to lower it from the exhaust. Easy peasy.
Bernard
Reviewed in the United States on July 8, 2017
Great buy for my 2.5`` Teraflex lift - Would recommend this if you have a 2012 and up JK. Hardest part to install was dealing with the old rusted bolts from the truck itself. Save yourself some trouble and soak up the flanges with WD40 and have a torch handy to blast them out.
James Shoptaw
Reviewed in the United States on October 6, 2017
I purchased Teraflex exhaust spacers over the others because it has been my experience that Teraflex goes the extra little bit to make quality products. Granted most of the time you do pay for it. That being said I was definitely not disappointed when I opened the box and found heavy duty spacers with the correct bolts for the application (apparently receiving the wrong bolts is a problem with the rugged ridge spacers). These appear to be milled instead of just bent pieces of pipe. Also, Teraflex has a good video on YouTube for the installation if you need it, although it is pretty straight forward. It took me about 45ish minutes to get these installed and I have all the correct tools. The hardest part was getting the y pipe bolt loose and slid farther in, but a good penetrating lube helped a lot. If you are needing exhaust spacers I definitely recommend Teraflex, they do cost a bit more but it's worth it in my opinion.
Pen Name
Reviewed in the United States on June 29, 2016
Works great, although people that have had there jeeps for a couple years might find it a little tougher to install due to any rust or carosion in the exahaust/exhaust clamp. Used PB blaster on mine and finally got it loose enough to be able to pry back to fit the spacer in. I know there just exhaust spacers, but they are very nicely machined. As with all Teraflex products, very good quality.
James K
Reviewed in the United States on November 10, 2015
I've only used them on a 3.5" AEV lift and they definitely helped. We still had to do some bending on our exhaust to get enough clearance for the front drive shaft. I don't know for sure but I think they would be more likely to work without the bending on a vehicle that's only being lifted an inch or two. The machining is top notch and the install isn't too difficult. For the price though it's not like you're going to get really hurt if they don't work. Definitely worth the money. Didn't experience rubbing or rattles as others described but Like I said we also did some bending. Also skid plates were not a concern for our build.