Your cart is empty.
Your cart is empty.Product Description
Your time is valuable
Doesn’t require the removal of the hub or the dust shield. Don’t waste your time replacing rusted, seized or broken dust shield bolts; with the 16002, you need only focus on the task at hand.
Practical & Accessible
Our press utilizes a 7/8” hex drive, meaning you don’t need any specialty tools for operation. And with an included bushing removal adapter, the Tiger Tool 16002 removes both the anchor pins and the bushings.
Sean E.
Reviewed in the United States on March 16, 2025
Purchased Tool To Remove Brake Anchor Bushings. It Didn’t Work Well On Split / Segmented Brake Housing. Tool was strong enough to bend the brake housing.This might work good on a solid housing but definitely not on a split. Gave 1 star because tool was robust
jesus
Reviewed in the United States on March 14, 2025
Works great, was using the recommended 3/4 impact(Milwaukee) but the anchor pins were stubborn not doing anything, ended up using the 1 inch hoping the tool didn’t explode on me slowly was getting it of … tuff tool no damage and did the job without having to heat or hammer it out, saves a to. Of time
Eric Custer
Reviewed in the United States on February 7, 2025
Excellent toll does a great job
Dean C.
Reviewed in the United States on August 13, 2024
Better than the heat and beat method.
snachtman
Reviewed in the United States on March 17, 2024
Works great! Much easier and faster than doing the heat and beat method
Slim
Reviewed in Canada on January 6, 2024
Strong and easy to use. Highly recommended
Ken
Reviewed in Canada on July 7, 2023
This press saved me so much my time and headache! As a professional mechanic needing to do brake jobs on semi trucks and trailers, this is a must have tool!
Calvin C Crewe III
Reviewed in the United States on May 14, 2023
Had a 1993 lowboy and all of the anchor pins were rusted. The Tiger Tool with a 3/4 drive Milwaukee M18 made short work of all the pins. Would recommend to anyone doing a lot of brake jobs and running into rusted anchor pins.
Customer
Reviewed in Canada on May 29, 2022
No dislikes
Richard Alberta
Reviewed in Canada on April 16, 2022
Well built product. Made life a lot easier
Brian Jones
Reviewed in the United States on August 13, 2021
and now i think i'm the second guy that actually changes the pins for the whole company. only seen 2 pieces of equipment where the pins had been recently changed, so someone else, probly the only guy that was doing them, had been there somewhat recently. that said...this tool is an absolute beast, i have no doubts in this tool whatsoever. the pins i'm dealing with are frozen solid with deep groves. i usually stall out my matco 2779 or makita xtw08, smack the webbing the sleves are pressed into till i get a nice bang from the pin and tool releasing pressure, then stall out my impact again and repeat till i can send it the rest of the way out. i think it would take a 3/4 or 1" gun to hurt this tool, but if she goes, she's gonna go big and take you with it! my only fear other than finding out what it will take to actually break this tool, is how easy it could be to lose the 2 adapter pieces. i don't know what the ring one is for and i'm too lazy to read instructions. the piece with the magnet is for the sleeves. the price is very painful, but once you have it in your hands you wont regret it... feels like 50# of finely ground forged unobtainium.
Travis G
Reviewed in Canada on September 14, 2020
Way quicker and easier than hammering and heating
HaabHauling
Reviewed in the United States on December 3, 2020
This tool is literally worth it's weight in gold. Match this with a 3/4" impact and you can remove both anchor pins and bushings in 5 minutes or less as you get used to using this tool. Just make sure you have a 3/4" drive 7/8" deep 6pt IMPACT socket. The only way this tool could be better is if there was a female 3/4" square drive directly cast into the tool rather than having to use a 7/8" socket.
Recommended Products