Tile Redi P3648C-PVC Shower Pan with Center Drain- Single Curb Shower Base, 2' PVC Drain, and Plate Included, 48' Width x 36' Depth

Use the base four times.Great product. Easy to work with.

Product description is 48x36 with center drain. The drain is not located in the center when measuring the width. Was not able to use the base due to this.

Be very careful when you buy these. They don't tell you on any of the literature, but 1: you can not use any adhesive except the epoxy adhesive provided. And it's very VERY expensive 6 pounds is almost $40. 2: some of their shower pans are not properly sloped (as pictured) I almost installed this one before I tested it. Water pooled in the center around the drain and in one of the corners. It never drained completely . This is bad news in a shower. . 3: install is not as easy as it seems. You are pouring a concrete base almost like a regular shower pan so, be ready with the proper tools. 4: all components like the drain, epoxy, and installed plumbing are proprietary sizes and materials. For example, you can not buy a drain cover off the shelf and use it with this pan.And lastly, buy it from Amazon, home depot or some other 3rd party dealer,and deal with them. The tile redi tile folks are difficult to deal with. The technical team is not very well versed in their product. I was trying to work with them on finding a fix for the one I bought one, but they were only able to give me basic info . They suggested sending extra epoxy and building the base slope up manually not realizing epoxy can't be used like that and, obviously, defeats the purpose of this product in the first place. I would not recommend this to anyone. KRBS makes a shower base that mortars into place like tile, and is compatible with off the shelf products like off the shelf mortars, drains, and drain.

Just got finished with installation. Worked like a charm with very little effort. Keeps things waterproof. Great for novice home renovations as instructions are easy to understand. Tile looks great and the corners are square!

Shower pan arrived on time, great product

Good tile ready base. Installation was difficult with the size and corner placement but successful. Good slope after tiling for drainage. Easy to use and tile. Solid once it was installed, no flex when embedded into the mortar.

I did a major master bath remodel, doing the tile myself and contractors for the plumbing, electric, and major carpentry. I have flipped both my first two houses, and this is the 3rd and final bathroom in my current house that I've remodeled, so I'm no stranger to all this. I had used the Redi Niche's in my last shower, and loved them. So easy to install and worth it. Originally, this shower pan (I got the 48 x 48 center drain) seemed like a better idea than having them frame a normal stall with a membrane. It wasn't. First off, my plumber installed it, and admittedly it was his first time installing it, but he's a seasoned plumber and I've used him on a bathroom before, water filtration, gas stove, etc. in the past. Smart guy, never had any issues.Problem #1: I don't know if the plumber didn't calculate the right amount of mortar for it to push all the way to the edge, or if some went through the subfloor near the drain, but one corner near the front dam was floating about 1/8-1/4 of an inch above the floor. When you stepped on it, it would wiggle. We didn't know this until after the mortar had all set. But if you turn this thing over, I'm not sure what the mortar would set to anyway near the front lip (where you step over the dam to get into the shower). It was all hollow and about 4 inches tall, as opposed to the center which was less than a half inch thick with ribs. What we did was butt the backer board up to the edge lips to press it down to make contact with the floor. This worked, but caused problem #4 below.Problem #2: The plumber inadvertently brought the pan out 1/2 inch from the studs in the back. The mortar had set by the time the carpenter saw this. I don't know if this was a brain fart on my plumber's part, but it would have been impossible to have this problem with a framed base and membrane. We ended up shimming the ENTIRE WALL of the bathroom half and inch between the studs and sheetrock, and I had to do a special frame for the door in that wall to deepen it. Real P.I.T.A.! Again, plumber's goof, but couldn't have happened going the normal route of framing a pan with a membrane.Problem #3: When the plumber went to test the drain, my ceiling downstairs got soaked. The drain fitting is very tight with very little leeway and even though he had glued it, we think that it had come loose likely when the contractors were putting the shower stall backer board in and walking on the pan. But also he said the drain was the black type of plastic and the pipes were PVC, so its possible the seal wasn't good due to the different types (I'm not a plumber). So, the wet ceiling downstairs came out, he fixed the drain from there, and I patched the ceiling back up after it dried out.Problem #4: After everything (including the shower glass) was in, that spot I referred to in problem #1 wasn't draining. Pushing it down to make contact with the floor was enough to mess up the slope. I ended up carving out the grout and removing the stones (the floor was river rock) one by one. After tearing a chunk of the shower pan out with one of the stones, I learned to do it EVER SO GENTLY. Others have commented how strong the epoxy you tile with is ... they aren't kidding. Luckily, it is so strong that I could just epoxy over the cracks and missing chunks I ended up creating in the pan while removing the tile. I don't worry about the water integrity --- that epoxy really is solid. But I ended up removing the whole corner and building up the epoxy base so that it would drain.Some of all of these issues was inexperience, but if a seasoned plumber had these issues I'd hate to think of what a DIY'er would go through. I thought it would save money and time, and ended up costing more and taking more time. It seems like a good idea, but really isn't. Both the plumber and the contractor said it would have been much easier just framing the pan and doing a membrane.I give it two stars (versus one) only because it is functional and everything works. Never again.

Excellent product. Easy to install and tile. The pan at first appears very light and unstable. Don't worry, after install, it is VERY stable.Make sure to follow the instructions regarding setting into mortar and tiling.Enough epoxy was provided to tile the entire pan and curb - make sure to read the instructions for epoxy and use the correct sized trowel. The epoxy dries quickly, so only mix enough for the section you are tiling. I poured the liquid parts of the epoxy (come in plastic bags) into empty water bottles. This allowed me to mix the epoxy in smaller amounts and there was no spillage. We broke a tile drill bit (when installing the shower door) when it hit the epoxy; it dries very hard and provides much of the stability. So, this is an important part.