Shopping Cart

Your cart is empty.

Your cart is empty.

uxcell B51 V-Belts 51' Pitch Length, B-Section Rubber Drive Belt 2pcs

Free shipping on orders over $29.99

$16.79

$ 7 .99 $7.99

In Stock

1.Size:40


About this item

  • Size: Pitch Length: 51"; Outer Girth: 1320mm; Inner Girth: 1251mm; Width: 17mm; Thickness: 11mm
  • Material: It is made of neoprene rubber for resistance to oils, water, and some solvents.
  • Function: To link two or more rotating shafts to transmit power in a drive system. Even load distribution on belt drives and good wear resistance.
  • Feature: The trapezoidal shape of the belts cross section wedges into the groove of a similarly shaped sheave or pulley to provide traction and alignment.
  • Applications: Used for drive systems in the automotive, agricultural, textile, printing, mining, and office equipment industries, ect.



Product Description

How to measure the length of the required belt:

  1. Wrap the rope around the two pulleys
  2. Make a mark
  3. Place the marked rope on a flat surface and use a tape measure to measure the distance between the two marks, which is the inner circumference of the belt

  • To accurately measure the length of the v-belt, use a belt measuring tool or a soft ruler, not a steel ruler.
  • The width and thickness of the belt should also be measured to confirm the type of belt.

Installation:

  • First, loosen the tensioning device, then press the v-belt into the pulley groove by hand, and finally tighten it again.

Notice:

  • Pay attention to the wear of the belt groove of the v-belt pulley.
  • Check whether the centerline of the two pulley shafts is parallel, whether the corresponding pulley slots are aligned, and whether there is any skewing phenomenon.
  • When one v-belt is badly worn and cannot be used, replace all the v-belts at the same time, with the same type and equal length, so that each belt has the same tension.

Maintenance:

  • Regularly check the v-belt tension, after adjustment still can not meet the specified requirements, must be replaced with a new v-belt.
  • In use, the operating temperature of the v-belt should not exceed 140°F, do not apply belt grease casually.
  • Various types of v-belt, should not be coated with rosin or sticky substances, but also to prevent v-belt from oil, butter and gasoline, otherwise, it will corrode the v-belt, and shorten the service life.
  • V-belt should be stored at a relatively low temperature, with no direct sunlight and no oil and corrosive fumes place.

Application

v belt

Lawn Care Equipment

  • Repair lawn equipment, snow removal machine

v belt

General Purpose

  • Repair band saw, box fan, drilling machine, trimmer

v belt

Automotive Repair

  • Replace the automotive belt
Customer Reviews
4.6 out of 5 stars 66
4.5 out of 5 stars 231
4.4 out of 5 stars 278
4.4 out of 5 stars 107
4.6 out of 5 stars 22
4.6 out of 5 stars 18
Type B A M K O SPZ
Width 16mm 13mm 10mm 8mm 10mm 10mm
Thickness 11mm 9mm 6mm 6mm 6mm 9mm

bill
Reviewed in the United States on May 6, 2024
worked as should
James Hilton
Reviewed in Canada on November 4, 2024
If you are a home handy guy, and do your research on the internet, to replace a B55 belt with this product is suppose to be 55+3 = 58 inches long. These belts are 55inches long.I finally bought from my local small engine repair shop.
Unknownphillip pittman
Reviewed in the United States on January 7, 2024
Worked great with the low price very satisfied
Bob
Reviewed in Canada on April 25, 2024
I ordered because I needed specifically a B53 belt for my skidsteer. This belt is too small to even install where I have used a B53 everytime in the past! This belt won't even get past the pulleys, never mind having the required play .
ChuckleHead
Reviewed in the United States on June 23, 2023
I have a Yardmax track barrel that has a belt on it that is labeled B32; which according to my research should be about a 35" belt (outside), but it actually only measures 33 1/2"...so I was confused.I ordered several other belts,: B29=32" too small, B30=33" still too small, B31=34" too large, B32=35" way too large; none fit properly. So, I tried this odd sized belt, and it fit perfectly...so go figure???Overall, it might not fit the standard measurements for B belts, but it is sized as described and it fit my application perfectly and since it comes in pairs I have a spare...but I still ordered it twice just to be sure...--I am happy with my purchase...
Glenn
Reviewed in the United States on June 16, 2023
To put it simply, this belt is not a standard B-32 v-belt. It is too short. It’s no good on my machine.
donald mackeller
Reviewed in the United States on November 9, 2023
This product is horrible, it is 1/2 smaller than the leading Belts as Gates or other name brands. I can not even use them.
Dave
Reviewed in the United States on April 24, 2023
I was hoping I could use it today, but the belt is about half the size of what I was getting.
Greg
Reviewed in the United States on September 16, 2022
Swamp cooler belt, bought two to have a spare. Well made.
Raymond Bishop
Reviewed in the United States on August 6, 2021
The belts look very good! The belts were mislabeled or just smaller than other B56 belts. Would not come close to fitting!
Client d'
Reviewed in Canada on February 27, 2021
Bon produit. Solide et lente à l'usure.Durable
Recommended Products

$12.61

$ 5 .99 $5.99

4.6
Select Option

$16.31

$ 7 .99 $7.99

4.6
Select Option

$17.95

$ 8 .99 $8.99

4.6
Select Option

$14.88

$ 7 .99 $7.99

4.5
Select Option

$36.83

$ 18 .99 $18.99

4.7
Select Option