Your cart is empty.
Your cart is empty.Product Description
Shipping Cu. Ft.:-1/4 - 1-1/4-Inch Jaw Width (In.): 3-1/4-Inch Length (Inches) (In.): 9-1/4-Inch.
From the Manufacturer
Wiss 3-Inch Hand Seamer, Straight Handle-HVAC.
Dave the Builder
Reviewed in the United States on May 11, 2024
I picked this one because I didn't want the same orange handled one that everyone else at work has. Tool works great but is not the same version.
dylanzago
Reviewed in the United States on April 24, 2024
With great force would work or the adjustment of the bolt would work but for the price tag these come with very disappointing would recommend a cheeper pare you will get same quality I normally swear by swiss
Makwa Stephen
Reviewed in Canada on August 11, 2019
Works good, good quality. Can’t go wrong with Wiss.
Customer
Reviewed in the United States on December 8, 2018
Just a high quality bender that I have had for about a year works great. I use it on metal roofing for folding various metal pieces where larger benders dont fit.
Customer
Reviewed in Canada on September 29, 2017
Great product!
Hvac jimmy
Reviewed in the United States on March 12, 2017
Dont waste your time with knock off and cheaper brands. You can not tell the difference looking at them but when you use them you'll know why you spent the extra cash. From the locking mechanisms that keep them closed while in your tool box to the mechanisms that is applying force when you squeeze the handle. Superior straightners.
DancersMom
Reviewed in the United States on February 20, 2016
Recently had a new variable speed Carrier furnace/blower installed, replacing a similar one that was over 13 years old and had catastrophically failed. My HVAC installers increased the return duct and return grill to the back of the house, just outside master bedroom. The air movement is awesome now but the new grill had an annoying harmonic resonance tone, particularly noticeable with cooling and even with heat at night. After lots of online research and several online suggestions from HVAC pros, I invested in this tool in order to open the return grill fins just a bit to hear if that made a difference, short of calling the pros back, replacing the grill, installing a new plenum above the return or the like. Worked liked a charm!! Easy peasy. Just grip with the tool and open the fins with one motion. Once I had opened up the two middle fin rows central to the 16inch duct opening above the grill (in ceiling), the harmonics lessened. Opened up each immediately outside rows to those two, and the harmonics stopped. The air movement noise remains slightly perceptible when I stand immediately under the return, but even then, it's not annoying. Worked very well!! Might or might not resolve your similar issue, but worth a try, I'd think before moving on to something more drastic of costly.
dan b
Reviewed in the United States on February 17, 2016
This is a great product. It grips metal evenly and makes it very easy to make bends right where you need them. The alignment marks on the lip eliminate the need to measure the distance on each bend.
JPPPP
Reviewed in Canada on December 12, 2016
Very sturdy and works well. Plates aren't perfectly aligned, but I don't think it matters, hasn't been an issue. I'm surprised the arms aren't longer to allow bends deeper than 1-1/4.
Lloyd Charles LaFontaine
Reviewed in Canada on December 1, 2016
It does the job. I have not identified any weak points.
Carl G
Reviewed in Canada on January 27, 2016
Well made heavy but works great .. you can put in many different angles and it holds your metal well.
Karen Kroupa
Reviewed in the United States on July 7, 2015
I use this tool to crimp hand-made key chains. A little duct tape applied to the plates (so it won't scratch the key fob) and they're perfect. The grip is small enough for me to use one hand. They have enough weight to them to make them sturdy but not so much that I get tired using them even after doing 50+ keychains in an hour.
R B C
Reviewed in the United States on July 27, 2013
Great price, and from a well known brand in the trades. Only problem with the tool is that the jaws are not even on the top edge. I kept them any way because I needed them for work, and didn't want to wait or bother with returning. I previously owned several Malco seamers (lost them). I liked them better but they are almost twice the cost. Over all an ok tool.
Recommended Products
