Shopping Cart

Your cart is empty.

Your cart is empty.

120-7012 Trailing Shield Flap Compatible with Toro 22' Recycler Lawnmower, Replacement 139-6604 145-5821 139-6597

Free shipping on orders over $29.99

$9.99

$ 4 .99 $4.99

In Stock

About this item

  • Part number:120-7012 139-6604 115-2893 139-6604 145-5821 139-6597
  • Compatible with Toro Model: 20332 20332C 20333 20333C 20334 20334C 20337 20338 20352
  • Compatible with Toro Model: 20353 20372 20373 20374 20376 20955 20956 20958 20960 120-7012, 22" Recycler Lawnmower Trailing Shield 115-2893
  • This is a new design for the old part 115-2893. It looks a little different, but that's okay. It will work properly at installation time.
  • Please Note: Fit all specs of above models listed, please consult owner's manual for proper part number identification and proper installation
  • Product size: Upper bottom: 17-3/4 inch, Lower bottom: 17-15/16 inch, Height: 5-1/8 inch (Manual measurement may have slight deviation)
  • The trailing shield is designed for when the mower moving forward only. Pushing the mower backwards when the trailing shield is installed will likely get damaged or broken by the blades inside. To maintain it service life, it is recommended to push the mower only forwards when the shield is installed on.



Product Description

Product details

3

Replacement part number:120-7012 139-6604 115-2893

Compatible model

Compatible with Toro 22 in Recycler Lawn Mower: 20332 20332C 20333 20333C 20334 20334C 20337 20337HD 20338 20340 20352 20353 20355 20357 20372 20373 20374 20376

Compatible with Toro 55CM Recycler Lawn Mower: 20955 20956 20958 20960 20961 20964 20965

3

Attaches at the rear of the mowing deck and trails across the grass

To secure to frame requires Toro Recycler Trailing Shield Screws (117-1092)

2

Installation steps

Turn the mower on its side and remove both rear wheels.

Loosen the locking screw from the trailing shield on both sides and remove the old shield.

Attaching the new trailing shield with the two locking screws and flat washers.

Reinstall the rear wheels

8

Product size

Length: 18 in

Width: 5.1in

Reminder: If you still do not understand the installation steps, you can try to search for the installation method on you tube. There are video tutorials above.


BOB N
Reviewed in the United States on February 17, 2025
As good as original.
A Raymond
Reviewed in the United States on February 10, 2025
It does not come with the screws as shown in pictures.
Dom S.
Reviewed in the United States on September 5, 2024
Easy to install, however you have to remove the back wheels toinstall it. When you remove the back wheels, be careful not toloose the washer that is under the wheel. Do it on concrete,, notgrass. Perfect fit! Use the anchors for an even tigher bite with thescrews.
Debi G. Sobieski
Reviewed in the United States on July 8, 2024
This item was made very poorly !! It did not do the job as the original one did. This Trailing Shield Flap DID NOT DO THE JOB !!!!!!!!! It got pulled under the lawnmower when I needed to back up & got chopped by the blade in the first maybe 10 minutes of use. So this was a very big waste of money !!!!!!!!!!!
Gerry C.
Reviewed in Canada on July 20, 2024
The Toro Lawn Mower rear skirt works well. It is a bit shorter and when I turn, there isn’t that side pressure that could make it rip over time. I did have to make some modifications though. The screws that holds it in place are too small and go through the holes on the lawn mower. I added larger washers that prevent the heads of the screws from going through the holes.
RB
Reviewed in the United States on December 7, 2024
The item was a direct replacement for the old one. Fit perfectly.
Joseph W Hall
Reviewed in the United States on December 19, 2024
Great Value
Dan B
Reviewed in the United States on October 28, 2024
After 2 years missing the back flap I looked this up on a whim. Surprised by how easy it was to replace. Does seem more rigid than original flap, but has held up good for 1st full mowing season
Maranara
Reviewed in the United States on October 21, 2024
Bought this flap to replace the original one on our toro recycler. So far it’s been great and hasn’t gotten stuck in the blade when backing up like the original one. It was a bit stiff at first but seems to be more flexible now
Randy Fidler
Reviewed in Canada on October 29, 2023
Just what I needed!