Shopping Cart

Your cart is empty.

Your cart is empty.

30 mm 35mm 40mm X-Tube Heat Shrink Sleeve Wrap Tubing for Fishing Rod Grips with Non Slip Waterproof and Insulation Lengths Durable Repair 39Inch(1M)

Free shipping on orders over $29.99

$8.99

$ 3 .99 $3.99

In Stock

1.Color:30mm Black


About this item

  • 【Wide Application】Heat shrink handle wrap to cover the handles of bypass loppers; replace hand coushions on crutches; to wrap crutch hand pads ; to wrap hockey stick grip ;to wrap fishing rods; to wrap sport grip ;to put on motorcycle grips; grips to down tubes and base tube (control bar) of hang-glider; fit on old hammer handles, wooden splintered rack handle and some of garden tools; use to cover old sticky handgrips ;use to cover roof rack bars ; ping pong paddle handle cover...
  • 【Easy to Use】The tube shrunk down perfectly using a heat gun. Another ways ,use a hair dryer then poured boiling water over it
  • 【Advantage】Thick material,fit and shrinkage good, add some nice grip, grippy and non-slip with wet hands;heat shrink grip is flexible, soft, shrink fast, stable, skid-resistant; the heat shrinkable tube with non slip, waterproof and insulation characteristics
  • 【Shrinkage Ratio and Temperature】Diameter thermal shrinkage ratio:2:1 of fishing rod grips; lengthwise shrinkage less than 8% ; shrinkage temperature60 ℃~105 ℃, the initial shrinkage temperature is 70 ℃,the minimum complete shrinkage temperature is 110 ℃
  • 【Storage】Please store unused rod handle shrink wrap in a cool place out of the sun.Great for fishing rod handles on salt and fresh water,hammer handles,cork handles, aluminum pipe,on the EVA foam rubber handles, lawn tools,pvc pipe...


How do we know what size to get?
1) Measure the diameter of the handle at the widest point on the grip
2) Use shrink wrap that is slightly larger
3) Most shrink tubes will have a final shrink diameter, for instance, reduces by 1/3 or by 1/2 max

Package :
1 Piece 30mmo or 35mm diamater (size of the tube before shrinking)1 meter/39Inch length

Kindly remind:
1) Heat gun is the best way in my opinion.(Heat guns are relatively inexpensive on amazon)
2) Used hair dryer should work but it may take longer
3) Used, torch, lighter before you need to be more indirect with the flame or can melt it


Booooolly
Reviewed in the United States on March 14, 2024
Different sizes makes it fit perfect.
Derek Vinyard
Reviewed in Mexico on January 20, 2024
Cumple su función, funciona para multiples usos
Rc
Reviewed in the United States on June 16, 2023
This is just what my rod needed like new now
Kris
Reviewed in the United States on October 19, 2022
I put it on the fishing rod handle it fits perfectly. I just wish I would have gone with the fish scale pattern I think that would have just looked better. But I definitely buy it again.
Kindle Customer
Reviewed in the United States on July 12, 2021
This worked great to improve the grip on a tomahawk while still remaining thin enough to slip the head off of the handle when necessary.
joel hernandez
Reviewed in the United States on June 8, 2021
Used it to add some more grip on the real seat. Great product and works great.
Landas Spencer
Reviewed in the United States on April 9, 2021
This work just like it was supposed to..thanks.
B. Stapleton
Reviewed in the United States on June 23, 2020
If you have a cork handle that needs a little TLC this is the stuff! Hi Don Richter rods were seeing a little abuse on the bottom end of the cork and I decided to give this stuff a whirl. Cut to length with with an 1/8 inch overlap allowing for the shrink to follow the contour and hit it with the heat gun. Very tight and clean finish.The material is very thick and should last quite some time I highly recommend.
Fred T.
Reviewed in the United States on November 22, 2019
Good stuff.
Recommended Products