Your cart is empty.
Your cart is empty.
SAE Battery Connector, SAE to O Ring Terminal Harness 2Pin Quick Disconnect SAE Battery Extension Cable with SAE RP Adapter, 10A/15A Fuses 2ft for Solar Panel, Motorcycle, Car, RV
- Type: Sae Connector to O Ring Terminal Harness
- With ring terminal connectors, attach to your battery charge directly, easy charge and quick disconnect.
- Sae quick connection with DUST CAP, protect the sae port from dust and raindrop when you don’t use it!
- Widely use with the battery chargers to keep the batteries in your cars, trucks, ATV and tractors charged, allow you leave the chargers near the wall plugs and not have to pull batteries to keep them charged with this sae to o ring terminal extension cable in the winter months.
- Works awesome to quickly attach trickle chargers to multiple batteries, easy to connect directly to bike battery and zip tie to frame for instant access via SAE connection. Makes using a battery tender easy-peasy.
- Suitable for most of vehicle use, like Motorcycle, Bike, Lawn tractor, Truck, Pickup, Snowmobile, Riding lawn mower, Boats, ATV, RV, Scooter, UTV, Kayak.
Tom
Reviewed in the United States on March 2, 2025
I started running battery tenders on my ATV and motorcycle years ago. More recently I wanted to able to add them to my garden tractors or at least be able to switch between easily. This 2 pack of connectors was my solution to that.They arrived in a small plastic box. Both 10 and 15 amp fuses were included for each. They are long enough that you can route them out of the way with tie wraps to your hood or chassis for easy access. The quality of the wire and connectors is just OK. It is more like a stiff plastic. Here in the cold weather of the northeast, they are very stiff. Rubber compounds would have been better. As others stated, the ring terminals are very thin but will do the job. As long as these don't break down and crack or short, they should be fine for trickle charging.I recommend these if you are looking to add some inexpensive connectors to additional vehicles to your seasonal charging needs.
Review 8672
Reviewed in the United States on February 28, 2025
I got these to leave permanently connected to my 12 batteries to connect to my charger. The metal terminals are thin and you'll probably want to put heat shrink at the ends to keep them from breaking off. Not the best quality for $5 each.
Pookie
Reviewed in the United States on February 27, 2025
I used these on an ATV and UTV so I could keep battery tenders on them.This kit feels perfect and I can leave them permanently on the batteries and use the cover to cover the ends when I'm using the ATV/UTV.Shipped and arrived quickly.
Darwin
Reviewed in the United States on February 25, 2025
These 2 SAE connectors are some of the better quality ones that I’ve found. The 2 connectors even came in a reusable plastic storage case. They include four fuses (both 10A and 15A), and the connector rings feature generously sized diameter holes that accommodate larger gauge battery accessory posts.While the listing specifies 16 AWG wire, it actually feels more substantial—possibly 14 AWG—which is definitely an advantage for durability and power handling capability.
Jim
Reviewed in the United States on February 24, 2025
SAE Battery Connector - 2 Pack, 2 FT SAE to O Ring Terminal HarnessThese are decent quality, nice ends and they fit together with other SAE cables I have on hand. The battery terminal rings are a bit larger than usual, but will work for most uses. You can always drill them out for larger terminal screws/bolts.The case they came in was unexpected, and would have been appreciated more if it did no have a crack that runs half way through the width of the case.There are 10 amp red fuses installed that are decent quality. They include two 15 amp blue fuses of equal quality, should you need/want to increase the capacity. No issues getting the existing fuses out like I have had with other SAE connectors.No complaints other than the cracked case that was meant to be a bonus.
Scott MacLean
Reviewed in the United States on February 24, 2025
This is a standard SAE-to-battery cable like the ones you typically find with Battery Tender type car battery maintainers. They are intended for trickle charging auto batteries.The connector, cable and fuse holder are of correct size and good quality. The ring terminals however are made of thin metal, and if subject to vibration (as they will be, in a car environment), I suspect they will eventually crack and break. Make sure you secure the cable to something so that it is not hanging by these terminals.The fuses included are 10 and 15 amp, and are correctly sized (not counterfeit fuses, like are so often being sold here).Who is this for?- Someone who needs additional connectors for battery mindersPros:- Good quality connector and fuse holder- Correct size wiresCons:- Ring terminals too thin for application
Robbin Chewings
Reviewed in the United States on February 24, 2025
I needed a quick connect for my LiFePO4 batteries for misc small load uses; trickle charging, discharge testing, etc. Since I have several premade cables with the SAE connectors this set of SAE cables is perfect for small loads. For larger loads I use Anderson SB50 connectors which I also have several cable sets.The downside of SAE connectors is there is no standard for positive/negative like Andersons. Like the other reviewer said, ALWAYS check your polarity when connecting SAEs. Of course, this set comes with a fuse so if you forget, no big deal, you just blew a fuse.
Matthew F.
Reviewed in the United States on February 22, 2025
This is an SAE connector built in with an inline fuse holder and ring terminals. The ring terminals can be connected to a battery and the SAE connector can be connected to an accessory with the corresponding SAE connector on the other end. I use these as a trickle charging port on my vehicles. This makes it easy to connect a charger when the vehicle will be sitting for a while. These connectors come pre-wired with the fuse holder and ring terminals. The wire is 16AWG so check the wire requirements of your equipment. The fuse holder comes with both 15A and 10A fuses for use with whichever is suited to your needs. The SAE connector comes with a rubber cap that securely fits over the ends when not in use. This will prevent unwanted dirt or water from getting into the connector when not in use. It will also keep accidental shorts from happening from something getting into the connector and touching metal on your vehicle. This 2 pack of connectors offers a great value. The wires measure exactly 24" from terminal to the tip of the connector. Always check to be sure the positive and negative side of the connectors correspond to the proper polarity on your accessory.
Recommended Products
