Your cart is empty.
Your cart is empty.Product Description
Perfectly fit forALL Yamaha Suzuki Johnson Evinrude trim and tilt end caps.
Designed to rebuild the leaked device on outboard engine, hydraulic trim and tilt unit Used to remove/ install the Trim and Tilt Caps without damage it and the steering cylinder.
This pin wrench tool will make it a breeze in removing trim/tilt. Helps you to open the cylinder in minutes without any grief and put it back together with confidence, effectively save your energy, time and money!
Operate easily, only makes both pins line up with the hole and insert, then work with 1/2" breaker bar (Not include).
MT0004
MORE SIZE WRENCHES
4mm | PINS SIZE | 4mm&4.5mm |
38mm | BETWEEN PINS SIZE | 32mm |
1x MT0004 Wrench | WRENCH QUANTITY | 1x MT0006 Wrench |
4mm | PINS SIZE | 6mm |
38mm | BETWEEN PINS SIZE | 35mm |
1x MT0004 Wrench | WRENCH QUANTITY | 1x MT0009 Wrench |
4mm | PINS SIZE | 4mm&4.5mm&6mm |
38mm | BETWEEN PINS SIZE | 38/32/35mm |
1x MT0004 Wrench | WRENCH QUANTITY | 3x Size Wrenches |
- MT0006
- MT0009
- MT0004+MT0006+MT0009
Freddie A.
Reviewed in the United States on March 5, 2025
Everything work like it should. Now if I ever need to work on another tilt and trim I have the tool for the job.
TC
Reviewed in the United States on March 17, 2025
I have a 2015 Yamaha F300 4.2l V6 outboard. Everything in the product description shows that this tool is the right fit for my tilt and trim cylinder caps. Sadly, the spacing on the tool was out of spec. It was slightly less than the 38 mm that is called for. The pins would not engage two holes in either cap at the same time. Unlike others who have purchased this tool, there was no way I was going to attempt to alter it or make it fit. This is a $16 tool and a replacement cap for my tilt cylinder is almost $100. Item was returned for a full refund. I ordered the proper AMT0004 tool directly from Marine Tech. I also confirmed with them that I was ordering the proper tool with a 38 mm span and 4 mm pins. I was fortunate and received a “used like new” tool for 1/3 off the retail price. This tool is also available here on Amazon.
Walton
Reviewed in the United States on March 16, 2025
Got it two days early and exactly what I ordered. Thank you.
Boatman7lakes
Reviewed in the United States on August 8, 2024
Works just fine
CoastalGuy
Reviewed in the United States on June 2, 2024
This fit perfectly and made removal of the trim cylinder cap easy. Just make sure you have the pins seated all the way and it should work fine.
Customer
Reviewed in the United States on April 26, 2024
MT0009 fits 90s model evinrude 40hp.. fit perfect plus i had to use breaker bar.. held up great.. hope this helps........
Puppy 1
Reviewed in the United States on July 14, 2023
Pins broke off in the cylinder cap. Just made the job more difficult
Client d'
Reviewed in Canada on May 15, 2023
trim bateau
Reed Phillips
Reviewed in the United States on May 10, 2022
Pros:-After much effort was able to make it work...destroying the tool and making future work on the hydraulic cylinder cap near impossible.Cons:-All the cons.....-Not Stainless, Nickel Coated, or in the white as shown in the picture. Came in raw coated steal that rubbed off while using.-DID NOT FIT THE HYDRAULIC CAP'S PIN HOLES. The Two adjacent holes were to close together (too small of a diameter). I could only get two pins (middle and one of the sides) to fit at any one time, left the third out which caused too much pressure on the two used holes.-Pins are not strong enough for the job, the screw heads broke off in use and the shafts deformed under pressure and bent, they are now unable to be removed or replaces.-The pins were not large enough to fill the cap's pin holes, causing them not to be fully supported in the hole and over stressing both the pins and the cap's pin holes. The cap's pin holes were carved out and now have essentially ramps on the edge that prevent the pins from grabbing. Think a feed ramp in a gun....I think I would have caused less damage to the hydraulic cylinder cap with a pipe wrench....
Murtadh
Reviewed in Saudi Arabia on March 14, 2022
لم تعجبني جودة الدبابيس
Recommended Products
$25.99
$ 10 .99 $10.99