Your cart is empty.
Your cart is empty.Product Description
Package Include:
- 1 x Pin vise,
- 1 x Bench vice,
- 2 x Keychain ring,
- 10 x PCB Mini Drill Bits,
- 48 x Twist Drill bits,
- 1 x Instruction,
- 1 x Box.
62 Pieces Pin Vises Hand Drill Bits
Pin Vise Hand Drill: Size: 3.74 inches/ 9.5 cm long How to use pin vise: Step 1: take out the suitable drill bit, and half unscrew the vise head. Step 2: half insert the drill bit, and screw the head tightly. Step 3: target the place where you are going to drill a hole, use one hand to fix the top of handle while using the other hand to rotate the handle.
Bench vice: Size: 4.3 x 2.4 x 1.4 inches Chuck clamping range: 0 - 57 mm Bench vice open diameter: less than 2.09 inches/ 5.3 cm
58 Pc Drill Bit Set
48 Piece Twist drill bit: Size: 3 Pieces of 0.5，0.6，0.7，0.8，0.9，1.0mm size, total 18 piece; 2 pieces of 1.1，1.2，1.3，1.4，1.5，1.6，1.7，1.8，1.9，2.0mm size, a total of 20 pieces; 1 piece of 2.1，2.2，2.3，2.4，2.5，2.6，2.7，2.8，2.9，3.0mm size, a total of 10 pieces;
10 Pieces PCB Mini Drill Bits: Material: Tungsten steel Size: 0.3-1.2mm The shank diameter is approx. 3.175 mm, overall length is approx. 38 mm, which fit for processing PCB, normal FR-4, CEM-3 boards, SMT, CNC, molds, plastic, circuit board, carbon fiber, composite board and so on
Method of Installation
- Choose the twist drill bit ;
- Slowly rotate the hand drill to make the three-jaw mouth chuck larger;
- Insert twist drill into the three-jaw chuck;
- Rotate the hand drill to tighten the three-jaw drill;
- Put the products that need to be fixed on the clamp;
- Use the demonstration.
Warm tips:
- Not suitable for hard materials like iron, steel, stone, glass, tile, etc..
- The pin vise is manual, not electronic.
- Small hand drill, only can clamp the drill bits of under 3 mm.
- Manual measurement, please allow slight difference.
jose o. madrid
Reviewed in the United States on September 16, 2024
What I was looking for was diamond coated drill bits. The kit had many drill bits except the ones I needed. I like the clamp and will use the drill bits that fit my drawer. Overall it is useful to me.
Robert Brake
Reviewed in Canada on March 9, 2024
Works great
Mark Rios
Reviewed in the United States on March 12, 2024
Nice product. The bits are very fragile,
Grandpa Shack
Reviewed in the United States on November 15, 2024
Hand drill seems to be good quality and is easy to use. The vise is good but not great. I am thinking it will be smoother with use. Work well and holds securely. All said a great value and I would buy again
Kesa Hopkins
Reviewed in the United States on November 12, 2024
THE TOOLS WORK GREAT- BE CAREFUL WITH THEM- AND THEY SHOULD LAST-
Bruce Beintema
Reviewed in the United States on October 22, 2024
nice variety of bits.
Miguel F.
Reviewed in Mexico on July 7, 2023
maravilloso simplemente nunca imagine tal grado dde fineza en su manufactura
Trevor Pool
Reviewed in the United States on December 31, 2023
I picked this kit up to use for building scale model cars. I enjoy building highly detailed models with brake lines, spark plug wires, and other details. These drill bits allow me to great whatever size hole I may need anywhere in the plastic of the kit. The drill bits are very sharp and quickly cut through the plastic. I unfortunately did break one of the very small micro bits when it rolled off my table onto the tile floor. I would just keep in mind the micro bits are super thin and easy to snap if not careful. The handdrill holds the bits securely and the rotating end makes for quick and easy drilling.
Jerry
Reviewed in the United States on March 3, 2022
If you are buying this set for the vice and drill, they are OK quality. Not great, but typical cheap china product quality - works but does not feel like quality.The drill bits are pretty bad. The good ones are not very sharp, and many came broken out of the package. probably half of the bits smaller than 1mm have issues - some are bent or broken, but the most common is the tip is machined so the point of the bit is right at one edge, rather than the center.The set of "CNC" bits in the case seem good, no issues with those. But the loose bits are a hot mess.
Christopher T Haynes
Reviewed in the United States on August 4, 2021
Only came with 7 of the 10 largest size bits. Bit sizes measured with digital caliper only approximately corresponded to the advertised sizes. The bits with colored bands come in a nice case; the others mixed in a single bag: plan to spend time with tweezers and caliper sorting them out. Then store them somehow: a scrap of proto-board was useful for the smallest ones, one per hole, and a SSD card flat case held the intermediate size ones ok. Surface vise is cheaply made, but seems ok for occasional use. Pin vise works ok: able to hold the smallest bit, contrary to the luck some others have reported. I've only enlarged a few circuit board holes so far, which it did ok with a .7mm bit
Recommended Products