Shopping Cart

Your cart is empty.

Your cart is empty.

Blue Sea Systems 3000 HD-Series Heavy Duty On-Off Battery Switch Grey

Free shipping on orders over $29.99

$59.99

$ 31 .99 $31.99

In Stock

About this item

  • Switches a single battery to a single load group Ignition protected - safe for installation aboard gasoline powered boats
  • IP66 waterproof, ISO 8846 and meets ABYC requirements
  • Accepts two 4/0 AWG (95mm²) battery cables.
  • Terminal Stud Size: 1/2"
  • Continuous Rating: 600A, Max Voltage: 32VDC


GREAT PRODUCT


JG
Reviewed in the United States on March 1, 2025
I upgraded my solar array and while working on it found out there was intense heat coming from somewhere (only 80 amps out of 200). Turns out the switch I had that was rated the same as this one was not actually very good. This one is a lot bigger and easier to get the 0/4 cable connected. I now run 200 amps through it and it doesn’t heat up at all.
Goody
Reviewed in the United States on June 7, 2024
Installed on my boat and so far it is working great.
Stainless
Reviewed in the United Kingdom on February 28, 2024
This very heavy duty battery system on/off 600 amp switch is typical Blue Sea System design quality. The knob turn action is very positive, with clear position indication. The 12mm threaded terminals are designed for heavy current use. It should give good service for a long time. The only additional feature that would be useful for me, is a small LED indicator to confirm when the current output is switched on.
FJ
Reviewed in the United States on December 10, 2024
Used as a battery disconnect switch on my sailboat bowthruster. Works well, very strong.
Behold
Reviewed in the United Kingdom on November 5, 2024
This thing is mental. build well and I do not believe it cannot handle the stated stats. and not a bad price either. using this to run 2 300amp output batteries with 600amp burst capability.
Blackwavyhair
Reviewed in Germany on July 16, 2023
Perfekt. Super schnelle Lieferung. Und wie alles von Blue Sea Systems top Qualität
FNO
Reviewed in Germany on June 10, 2023
Absolut solide und robuste Qualität!Ist in einem Ducato zu Trennung der Starterbatterie eingebaut. Trennt zuverlässig und dauerhaft ohne Ermüdungserscheinungen.Kaufempfehlung.
Don and Johns Rv life
Reviewed in the United States on October 11, 2023
Love it and feel it is a quality product. Works as designed
Customer
Reviewed in the United States on September 4, 2022
This switch is super heavy duty. It is good quality and works well. Used it in my RV solar install and was probably more switch then I needed which made it somewhat hard to work with for my needs.
Johnny's
Reviewed in the United States on February 14, 2022
Another excellent blueseas switchActual switch size is 4 inches W X 4 inches L and about 3 inches high laying flat on it's back on a table.It is definitely NOT the same size of the regular lower capacity switches from blueseacontinuous current up to 600 amps20 second burst current of 1600-1700 amps @ 12 V
N. Edgar
Reviewed in the United States on August 31, 2020
Well made. Using for my winch in the Jeep and needed something that would hold up to 450 amps at full draw, this should do it.I’ll be installing as a surface mount with non-conductive material immediately below the lugs as they will be fairly close to the surface.After burning up one winch motor with a short I hope to prevent that, or worse, with this switch.
Customer
Reviewed in Canada on October 4, 2018
As describedPRO: Great quality. Large high power 1/2" terminal studs (vs 3/8).CON: No back cover to protect terminal studs.
Volt Doctor
Reviewed in the United States on April 23, 2018
High quality switch that is ignition protected and IP66 waterproof rated. The connection studs are tin plated and long enough for each to hold multiple cable lugs. One side of the "single circuit" switch version (3000) has two lugs in common so there is even more room for cable connections. The 600A continuous, 900A (5 min) and 1750A (30 sec) ratings are adequate to handle heavy duty applications on boats and motorhomes. Note that the cable lug studs are for 1/2" diameter lugs, so if you are relocating cables from some other source you may need to drill out or replace your cable lugs. I have installed several of these and have never had a problem or failure.