Your cart is empty.
Your cart is empty. Features:
* Working voltage DC 10V-35V. Recommended to use a switching power supply DC24V power supply.
* 6N137 high-speed optical coupling, guarantee high speed without losing step.
* protection circuit to ensure optimal performance.
* Rated maximum output: ± 3A, peak 3.5A.
* For two-phase within 42,57 stepping 3A / four-phase / of line four / six-wire stepper motor, and is not suitable for more than 3A stepper motor.
* Automatic half current function.
* Subdivision: whole step, half-step, step 1/8, 1/16 step, a maximum of 16 subdivisions.
Specifications:
* Working voltage:DC 10-35V
* Rated maximum output: ± 3A, peak 3.5A
* Main color:Green
* Size:75 x 50 x 33mm
* Net weight:83g
* Package weight:93g
Attenuation adjustable (Decay Mode)
0 %---- no decay mode
--- 25% of the slow decay mode
--- 50% of the normal mode
100% - Fast Decay mode
----- Decay mode of regulation by different motors to match impedance, thereby eliminating the noise when locked stepper motor and motor movement in the shake.
Automatic half current setting (Torque Settings)
%---- No pulse when the current 20 to normal operating current of 20%
50 %---- no pulse current 50% to normal operating current
75 %---- no pulse current 75% to normal operating current
100% --- no pulse when the current 100% to normal operating current
Package Included:
1*TB6560 Stepper Motor Driver Board
MD
Reviewed in the United States on September 28, 2023
I ordered one of these for a stepper motor. The board came in crushed, like a forklift ran over it. I ordered these before and had the same issues. I got one good board 1 time. Amazon made it good when there was a problem.
Carlos P
Reviewed in the United States on January 29, 2023
UPDATE:Resoldered all components in the PCB, and the device started to work!---------------------I am very disappointed with the performance of this device. I intend to use it in a project to drive a .8 A NEMA 11 stepper drive with practically no load and use an Arduino Nano to generate the pulse/direction signals.The project requires the motor to run at 360 RPM constant speed for about one minute, stop 2 seconds and start again. I tested all combinations of excitation modes (0, 1, 2, 8, and 16) and all the decay settings combinations with unsatisfactory noise, speed, and direction results.- The motor would change direction randomly when applying minimum load. The speed is inconsistent with decay settings.- Sometimes, the motor runs at half the speed at max decays.- There should be a connection or soldering issue in the PCB of the device as it is affected by vibration.In the end, my system works better with an A4988 Stepper Motor Driver than with this device.
B.S.C. GUITARS
Reviewed in the United States on August 25, 2022
I use this on my homemade CNC router and it is outperformed even more expensive drivers so I will definitely get a couple more
All Outta Bubble Gum
Reviewed in the United States on May 1, 2022
I got a driver missing an SMD component. If you need 10, order 12 and return the extras if they are still good.
Max
Reviewed in the United States on November 3, 2022
Would give 3.5 stars if possible. It does work properly (so far). Just noting the condition and presentation.One of the switches is cracked and missing the lever, and another switch is improperly mounted on the board. Had to use tweezers to carefully adjust broken switch. The text is very blurry and difficult to read and the whole board was covered in a nasty residue.
dalwindersingh
Reviewed in the United States on October 31, 2020
I like it it does the job .I wounder why they think late to add cooling fan for this. It was failing because of over heating now it is works fine. They should give some documentation how to add height probe and software to compensate leveling etc.
Vincent Z.
Reviewed in the United States on November 5, 2018
I'm a first time experimenter with steppers and was very easy to set up. Works great.
VE208532 Jose Pujol
Reviewed in the United States on November 24, 2016
Excelent!!!!!
Recommended Products
